Keysight Technologies 85058V Скачать руководство пользователя страница 51

Страница: 51 / 58

85058V

6-5

Replaceable Parts

Replaceable Parts

Table 6-2

lists the replacement part numbers for items included in the 85058V verification kit

and

Figure 6-1

illustrates the attenuators and beaded lines.

Table 6-3

lists the replacement part numbers for items not included in the verification kit that are

either required or recommended for successful operation of the kit.
To order a listed part, note the description, the part number, and the quantity desired.

Telephone or send your order to Keysight Technologies. Refer to

page 5-6

Table 6-2 Replaceable Parts for the 85058V 1.85 mm Verification Kit

Description

Qty

Per Kit

Keysight

Part Number

Attenuators

40 dB attenuator with data

85058VR02

10 dB attenuator with data

85058VR01

Beaded Lines



beaded line with data

85058VR03



mismatch beaded line with data

85058VR04

Miscellaneous Items

Storage unit:

Box

5180-7899

Foam pad, bottom

85058-80127

Foam pad, top

5180-8490

User’s and service guide

85058-90007

See “Printing Copies of This Document” on page ii.

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды