Keysight Technologies 85058V Скачать руководство пользователя страница 48

Страница: 48 / 58

6- 2

85058V

Replaceable Parts

Replacing the Verification Data

The verification data contains unique performance data that applies to the individual verification

devices. No two devices have the same performance data. It is not a trivial matter to replace

lost or damaged data, so it is important to make one or more backup copies.
If your verification data is lost or damaged, and you have no backup copies, take one of the

following actions:
•

If recertification is not required in the near future.

Contact Keysight for replacement verification data - refer to

“Contacting Keysight” on

page 5-6

. Please specify the information in the table below.

•

If recertification will be required in the near future.

Keysight recommends that you have the verification kit recertified early. New verification

data will be generated during the recertification process. Refer to

“Recertification” on

page 4-3

Table 6-1 Information to Specify When Ordering Replacement Verification Data

Device

Model Number

Serial Number

Part Number

Kit

Device 1

Device 2

Device 3

Device 4

Needed:

(check) PNA USB drive ___; Data sheets ___

Last Recertification:

Date _______________; Serviced by:

___________________________________________

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды