2- 4
85054B
Specifications
Mechanical Characteristics
NOTE
The gages for measuring type-N connectors compensate for the designed offset
of 5.26 mm (0.207 inch), therefore, protrusion and recession readings are in
relation to a
zero
reference plane (as if the inner and outer conductor planes were
intended to be flush). Gage readings can be directly compared with the
observed
values listed in
.
The pin depth value of each calibration device in this kit is not specified, but is an important
mechanical parameter. The electrical performance of the device depends, to some extent, on
its pin depth. The electrical specifications for each device in this kit take into account the effect
of pin depth on the device’s performance.
lists the typical pin depths and
measurement uncertainties, and provides observed pin depth limits for the devices in the kit. If
the pin depth of a device does not measure within the
observed
pin depth limits, it may be an
indication that the device fails to meet electrical specifications. Refer to
for an
illustration of pin depth in type-N connectors.
NOTE
When measuring pin depth, the measured value (resultant average of three or
more measurements) is
not
the true value. Always compare the measured value
with the observed pin depth limits in
to evaluate the condition of device
connectors.
Table 2-2 Pin Depth Limits
Device
Typical Pin Depth
micrometers
(10
–4
inches)
Measurement
Uncertainty
a
micrometers
(10
–4
inches)
a. Approxi2 sigma to
2 sigma of gage uncertainty based on studies done at the factory
according to recommended procedures.
Observed Pin Depth
Limits
b
micrometers
(10
–4
inches)
b. Observed pin depth limits are the range of observation limits seen on the gage reading due to
measurement uncertainty. The depth could still be within specifications.
Opens
0 to
12.7
(0 to
5.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
16.5
(+ 1.5 to
6.5)
Shorts
0 to
12.7
(0 to
5.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
16.5
(+ 1.5 to
6.5)
Lowband
loads
0 to
50.8
(0 to
20.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
54.6
(+ 1.5 to
21.5)
Sliding loads
0 to
7.6
(0 to
3.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
11.4
(+ 1.5 to
4.5)
Adapters
(7 mm end)
0 to
50.8
(0 to
20.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
54.6
(+ 1.5 to
21.5)
Adapters
(type-N end)
0 to
12.7
(0 to
5.0)
+3.8 to
3.8
(+ 1.5 to
1.5)
+3.8 to
16.5
(+ 1.5 to
6.5)
Содержание 85054B
