manualshive.com logo in svg

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Keysight Technologies 8480 Series Скачать руководство пользователя страница 59

Service

3

Keysight 8480 Series Operating and Service Manual

59

Troubleshooting

Troubleshooting information is intended to first isolate the Power Sensor or the 

Power Meter as the defective component. When the Power Sensor is isolated, 

troubleshooting information is intended to identify the A1 Bulkhead Assembly or 

the A2 Power Sensor Board Assembly as the defective component.
Before you open the Power Sensor to continue with the troubleshooting 

procedures, try the substitution method of elimination. Use another power meter, 

known to be in good operating condition, with the suspected power sensor and 

cable. If the same problem occurs with the “known good” power meter, substitute 

a “known good” power sensor cable.
Troubleshooting should be performed with the Power Sensor opened, and the 

printed circuit board exposed. Refer to the “Disassembly / Reassembly 

Procedures” on page 69.
When a failed assembly has been identified, refer to the repair section in either the 

“A1 Bulkhead Assembly” on page 63 or the “A2 Power Sensor Board Assembly” on 

page 64.

Troubleshooting - eliminating the power meter and sensor cable

Where a “known good” power meter and/or sensor cable is unavailable, another 

means must be used to isolate the fault to the power sensor.

NOTE

The FETs in A2U1 are light sensitive, and dc levels are shifted slightly when the 

FETs are exposed.

CAUTION

Excessive power damages the power sensor.

CAUTION

Electrostatic discharge renders the power sensor inoperative. 

Troubleshooting and Repair procedures must be carried out at a static free 

workstation.

Содержание 8480 Series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды