Keysight Technologies 8480 Series Скачать руководство пользователя страница 69

Страница: 69 / 99

Service

Keysight 8480 Series Operating and Service Manual

Disassembly / Reassembly Procedures

Disassembly Procedure

Disassemble the Power Sensor by performing the following steps:

Insert the blade of a large screwdriver between the two-piece plastic shell at

the rear of the Power Sensor. Gently pry the sections apart. (See .)

CAUTION

Disassembly must be performed in sequence described in the following

procedure, otherwise damage may be caused to the two gold wires between

the bulkhead assembly and the Power Sensor Board Assembly. If these wires

are damaged, the A1 Bulkhead Assembly must be replaced.

NOTE

Every power sensor has an individually prepared label on the housing. If more

than one power sensor is disassembled at a time, be sure to mate the correct

power sensor and housing when reassembling.

Содержание 8480 Series




































































































Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды