Subject to modifications.
2/ 4
G
Display and operating elements
Basic settings
Programming details
8.1 Manual/automatic operation mode
Once the device has been correctly installed and the power supply swit-
ched on, the current time will be displayed on the control display. By
default the control system operates in manual operation mode and all
automatic functions – like sun- and time-dependent controls – are disabled.
8.2 Switching from manual operation to automatic operation
To activate automatic mode, press the
m
button for 3 seconds followed
by the
h
button. The control indicates the change of operating mode by
displaying
AUTO ON
. Now press the
u
button until
EXIT
is displayed.
Exit the menu by pressing the
.
button. The automatic control is acti-
vated and the shutters now move up or down at the programmed times.
However the shutters can still be raised or lowered outside of the pro-
grammed times by pressing the
up
or
down
button. To stop the shutters
moving up or down, simply press the
s
button.
You can switch operating modes at any time. To revert to manual mode,
proceed as described above and switch off the automatic function.
The control system features a wide range of functions which can be set to
meet your individual requirements.
Press and hold the
m
button for 3 seconds to go to the
programming menu.
There are two ways to set values in the individual menus: briefly press for
step-by-step programming, or press and hold for more than 2 seconds to
scroll through the available values using the
2
and
1
buttons.
Return to the previous menu by pressing
BACK
. Press
EXIT
to exit the
programming menu immediately. Any programming changes are saved
automatically and immediately. If no buttons are pressed for over 3 minutes
in the programming menu, the programming menu will close automatically.
IMPORTANT!
If an up or down command is being performed, it must first
be interrupted by pressing the
s
button to call up the
menu.
i
Manufacturer’s default setting
Time and date are factory preset. The following settings are also preset but
may be adapted to your own personal requirements as necessary.
Automatic functions “AUTO”:
Off
Function „SUN“:
Off
Function „RANDOM“:
Off
Function „ASTRO“:
Off
Function „TIMER 1“:
On
Function „TIMER 2“:
Off
Setting „LANGUAGE“:
German
Setting „LOCATION“ Postal Code:
34117
Setting „CORRECTION“ Up:
0 minutes
Setting „CORRECTION“ Down:
0 minutes
Setting „MOTOR“ Runtime:
120 seconds
Setting „MOTOR“ Tilt Time:
0.0 seconds
Setting „MOTOR“ Inching Mode:
Off
Setting „KEYLOCK“:
Off
Power failure / Replacing the Battery
In the event of a power failure, the control is equipped with several years'
reserve power. As soon as the mains power fails, the display will start to
flash and after 5 minutes it will switch itself off. This does not mean that the
battery is flat! When the mains power returns, the control system will
display the correct time. If an up or down command is pending during the
power failure, this command will be automatically carried out when the
mains power returns. If, after a power failure, the control system no longer
displays the correct time or date you probably need to change the battery.
In this case, proceed as follows:
– Hold the display frame and gently remove the operating device from the
power supply. You will find a CR 2032-type battery in the back of the
operating device.
– Remove this battery and replace it with a battery of the same type
(make sure you insert the battery correctly).
– Now plug the operating device into the power pack.
To set the time, proceed as described in the “Programming menu – Settings,
time” section.
Installing the lux sensor
For the sun function, one lux sensor is required per control system. Only
1 lux sensor may be connected. The sensor cable must not be extended.
Install the sun sensor as follows.
1. Remove the operating device from the power supply.
2. Plug the lux sensor connector into the socket on the front of the power
pack.
3. Gently press the operating device back into the power supply.
4. Attach the lux sensor at the desired location on the window pane.
5. Switch on the sun function.
6. Switch the control system to automatic mode.
IMPORTANT!
Your personal settings are stored electronically and will not be
lost when you replace the battery.
i
The disposal of electrical equipment and batteries in household waste
is strictly forbidden.
The symbol (dustbin crossed out, in line with WEEE Appendix IV)
indicates separate collection of electrical and electronic products
in EU countries. Do not dispose of the device or battery in your
household waste. Ask your town or local council about the return
and collection systems available in your area to dispose of this
product.
É
Disposal of waste
Shutter Control
©
KeyLink International
Ar
t.-Nr
.:
85201821 D1 •
K
eyLink International
•
K
erkhofstraat 21
•
N
L5554 HG Valkenswaard
• www
.
keylink.nl
