6
7
Quick Setup Guide
1.
Begin with the KD-MAX8x8 and all Input/Output devices turned off and power cables removed
2.
Connect analog audio sources to the desired 6-pin phoenix terminals and/or digital audio
sources to the desired PCM inputs
3.
Connect the analog audio output amplifiers/receivers via the analog 6-pin phoenix terminals
and digital destinations via the PCM outputs
4.
Connect power to the KD-MAX8x8, followed by all other input and output devices and turn
them on
5.
If balanced audio input type is required for any of the analog inputs, set the desired input via
the IR remote control using command sequence R2, XX, Audio Mode, 3. Note that XX is the
desired input number (01 – 08).
6.
Operate KD-MAX8x8 switcher via the front panel buttons, IR remote, serial IR or RS-232
control
7.
See TCP/IP and RS-232 Commands or Settings and Adjustments via Remote sections for
more adjustments options
Settings and Adjustments via Remote
Many initial installation steps may be configured using the factory remote control. Other advanced
settings may be configured using USB and software downloaded from www.keydigital.com
1
2
3
4
5
6
7
8
9
0
All Mute
Volume
Mute
Audio Mode
Video Mode
Balance
LipSync
Bass
Middle
Treble
Restore
All Restore
R1
R2
R3
R4
Power Off
Power On
www.keydigital.com
Tone Controls
Input Associated Audio Type
»
IR Button Sequence = R2, XX, Video Mode, Y
»
XX = Input # [01-08]
»
Y = Audio Type [1 = Analog, 2 = PCM, 3 = Analog to Analog,
PCM to PCM]
Analog Input Audio Type
»
IR Button Sequence = R2, XX, Audio Mode, Y
»
XX = Input # [01-08]
»
Y = Audio Type [1 = L+/R+, 2 = L-/R-, 3 = Balanced, 4 = N/C]
Matrix Switching Command (Associated Audio)
»
IR Button Sequence = Audio Mode, X, Y
»
X = Output # [1-8]
»
Y = Input # [1-8]
Output Mute/Un-mute
»
IR Button Sequence = R1, X, Mute/Restore
»
X = Output # [1-8]
Output Volume Up/Down
»
IR Button Sequence = R1, X, Volume, Up/Down
»
X = Output # [1-8]
Output Volume Level
»
IR Button Sequence = R1, X, Volume, YY
»
X = Output # [1-8]
»
YY = Volume Level [00-99]
Set Unit Static IP Address to xxx.xxx.xxx.xxx
»
IR Button Sequence = R3, Bass, XXX, Video Mode, XXX, Video Mode, XXX,
Video Mode, XXX
Set Unit Default Gateway/Router IP Address to xxx.xxx.xxx.xxx
»
IR Button Sequence = R3, Treble, XXX, Video Mode, XXX, Video Mode, XXX,
Video Mode, XXX
»
Default IP address is 192.168.1.239, with default port 23 and default gateway 192.168.1.1
»
Please see the IR Remote Command List section for additional commands
Apply New Network Configuration
»
IR Button Sequence = R3, All Restore
IR Remote Command List
IR Control is possible using remote model KD-REMOTEHM88 (included). Use the numerical
keypad for X, Y, and Z values below.
Advanced unit setup should be completed in the KD Wizard software found on
www.keydigital.com
Command
Sequence
Input Setup
Parameters
XX = input # (01-08)
Input associated input type
R2, XX, Video Mode, Y
Y = 1 (Analog) / 2 (PCM) / 3 (both)
Set analog input type
R2, XX, Audio Mode, Y
Y = [1 = L+/R+, 2 = L-/R-, 3 = Balanced, 4 = N/C]
Audio Output Setup
Parameters
XX = 01 – 08
YY = 01 – 99, Up, Down
Set Output X to Association Input Y
Audio Mode, X, Y
X = Output #[1-8]
Y = Input #[1-8]
Set digital output XX = Analog input YY
R1, XX, Video Mode, YY
Set digital output XX = PCM input YY
R1, XX, R2, YY
Set PCM output XX = PCM input YY
R1, XX, R3, YY
Set ALL output Mute/Unmute
All Mute/All Restore
Set output XX ON/OFF
R1, XX, R4, 1/0
KD-MAX8x8 Manual.indd 6-7
12/23/17 2:18 AM
