Kewtech KT35 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Kewtech KT35 Скачать руководство пользователя страница 5

3

temporary

link

test at socket

between L and E

Typical arrangement for measuring the continuity of protective

conductors. Before proceeding with tests conductors must be

proved to be de-energised.

▲

200mA continuity short circuit test current

▲

1mA test current at the minimum load on insulation ranges

▲

Bar graph indicates test voltage-rise and decay can be
observed during insulation tests

▲

Warning of external voltage presence

▲

‘Press to test’ button with lock down feature. Releasing the
test button automatically discharges the capacitance of a
circuit under test

▲

Auto null feature

2.2 Principles of Measurement

An Insulation/Continuity Tester performs two basic functions.
As a continuity tester the instrument can be used to measure
low values of resistance between two points in an electrical cir-
cuit. In this mode the instrument acts as a low voltage current
source. The resistance is calculated from the measurement of
the voltage and the current through the conductor. Careful

«
...
3
4
5
6
7
...
»

Содержание KT35





















Отзывы:

Нет отзывов