manualshive.com logo in svg

Kett MT-730, Руководство по эксплуатации

Поделиться
Скачать
Kett MT-730 Скачать руководство пользователя страница 13

13

6-3. Setting the Measurement Mode

There are two measurement modes: “Normal measurement mode” and “Continuous measurement mode”. 
Immediately after pressing the 

 key and turning on the power, the unit will be set to “Normal 

measurement mode”. If the unit is set to “Continuous measurement mode”, measurements can be made 
without pressing the 

 key for each measurement.

1. Continuous measurement mode setting
  In step “6-2. Measurement Method 4. Press the...”, press the 

 key. The decimal point will blink, and the moisture 

value and bar graph will be displayed. “LO” will be displayed, 
and the decimal point will blink when the needle probe is not 
inserted into the wood or if the wood moisture value is below 
the measuring range.

2. Canceling the continuous measurement mode
  Press the 

 continuously for at least 2 seconds until a 

“beep” sounds. The display will momentarily go blank. When 
you take your finger off the key, the unit will return to normal 
measurement mode.

•  Pressing the 

 key turns off the power and automatically 

cancels the unit.

•  Note that the battery life is shorter in continuous measurement mode.

• The 

 symbol denotes a blinking display.

Содержание MT-730

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды