manualshive.com logo in svg

Keston Qudos 28s, Инструкция для пользователя, по установке и обслуживанию

Поделиться
Скачать
Keston Qudos 28s Скачать руководство пользователя страница 4

0. HANDLING INSTRUCTIONS

0.1

LIST OF CONTENTS

The Keston Qudos 28s and Qudos 28sP are supplied almost totally pre-assembled. The units
use standard 50 mm muPVC (BS5255 and/or BSEN1566-1 and BSEN1329) pipe for the flue
and  air  intake  systems.  The  boiler  is  packed  in  a  single  box  without  additional  flue  kit.  All
additional  components  are  packed  inside  the  boiler  cabinet  itself.  The  following  is  a  list  of
components and their location in the boiler cabinet 

Equipment List
Item

Quantity

Location

Wall Bracket Rawl Plugs

6

Inside accessories bag

Wall Bracket Wall Fixing Screws

6

Inside accessories bag

Wall Mounting Bracket

1

Secured to inside right 
hand side of boiler case

Wall Mounting Bracket Nuts

1

Inside accessories bag.

Wall Mounting Bracket Washers

1+1

Inside accessories bag

Wall Bracket Bolt Insulation

1

Inside accessories bag

50 mm muPVC Air/Flue Terminals

2

Inside accessories bag

Air Inlet Spigot (50 mm)

1

Inside accessories bag

Flue Outlet Spigot (50 mm)

1

Inside accessories bag

Air Inlet Spigot Gasket

1

Inside accessories bag

Air Inlet  Flue Outlet Spigot  M6 Screws 4+2

Inside accessories bag

Cabinet Cable Entry Clamps

2

Inside accessories bag

Gas Isolating Cock

1

Inside accessories bag

Condensate Trap

1

Inside accessories bag

Condensate Trap fixing screws

2

Inside accessories bag

Condensate Trap fixing washers

2

Inside accessories bag

Condensate Trap Gasket

1

Inside accessories bag

50 mm muPVC Pipe

2

Inside boiler case

50 mm muPVC Elbow

2

Inside boiler case

Document List
Item

Quantity

Location

Registration of Purchase

1

In A4 envelope

Installation Template

1

In document bag

Remove the cabinet shell by removing the two retaining screws in the top of the cabinet and
the two retaining screws in the bottom of the cabinet.

0.2

RECOMMENDED HANDLING PROCEDURE

NB  :  The  following  lift  operation  exceeds  the  recommended  weight  for  a  one-man  lift  as
specified in the Manual Handling Operations 1992 Regulations.

For  the  carriage  of  carton  it  is  recommended  at  least  two  people  perform  any  lift.  Clear  the
carriage route of the carton from point of delivery to point of installation. Take care to avoid trip
hazards, slippery or wet surfaces and when climbing steps and stairs. Always use assistance
if required. If a sack truck is used it is recommended the carton is strapped to the truck. 

For  the  unpacking  of  the  appliance  from  the  carton,  it  is  recommended  at  least  two  people
perform any lift. It is recommended to cut the base end of carton and open the carton flaps.
Ensure the protective packing over the boiler tappings at the base of the boiler is kept in place,
then tilt the boiler forwards from its back onto its base and remove carton by sliding up over
the  boiler.  When  lifting  this  appliance  the  back  should  be  kept  straight  at  all  times.  Avoid

WD420/3/2007

The Keston Qudos 28s & Qudos 28sP Boilers

Page :  iii

Содержание Qudos 28s




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды