manualshive.com logo in svg

Kersten UBS Easy 13 GE, Оригинальная инструкция по эксплуатации, Страница: 25 / 29

Поделиться
Скачать
Kersten UBS Easy 13 GE Скачать руководство пользователя страница 25

22 

Fault cause and remedy 

13 

Fault cause and remedy 

This chapter describes in more detail the most important faults that can occur during operation 
on the hydrostatic single-axle unit. Faults which require major intervention must always be 
rectified by your specialist workshop. 

Observe safety instructions! 

Disorder: 

Possible causes: 

Remedy: 

Gasoline engine: 

Gasoline 
engine does 
not start 

-  Spark plug connector not plugged in 

Plug in the plug

-  Move choke lever to choke

position position

-  Switch motor off switch to position "I"

- Safety circuit not in

Bring safety circuit into

starting position

starting position

-  Fuel talk empty or

Fill the fuel tank with fresh fuel

Bad fuel

-  Clogged fuel line

Clean fuel line 

-  Spark plug defective

Clean, adjust or replace the spark plug 

-  Engine too much fuel (flooded)

Dry, clean and start the spark plug 

with FULL GAS 

-  Motor off line defective

Check cable and plug connections 

-  False air due to loose carburettor

Tighten fastening screws 

and intake pipe

Gasoline engine 

- Engine is running in the CHOKE area  Move the choke lever to the operating position

Has dropouts 

- Ignition cable loose

Plug the spark plug connector firmly onto the 

ignition cable. Secure the ignition cable 

fastening Fit the spark plug plug firmly onto 

the spark plug 

- Clogged fuel line or bad fuel

- Ventilation in the fuel tank cover

congested

Change fuel filter or refuel with fresh 

fuel Replace fuel tank cover 

- Water or dirt in the fuel

system

- Air filter dirty

Drain fuel and clean, refuel with 

fresh fuel 

Clean or replace the air filter 

- Carburetor adjusted

Adjust carburetor 

Gasoline engine 

- Too little engine oil

immediately refill engine oil 

Gets too hot 

- Cooling air system restricted

- Air filter dirty

Clean fan grille, clean internal 

cooling fins 

Clean or replace the air filter 

- Carburettor not set correctly

Adjust carburetor 

Gasoline engine 

- Ignition distance too low

Adjust spark plug 

Has dropouts 

- Idle mixture not set correctly

Adjust carburetor 

At high speeds 

correctly

Gasoline engine 

often idles 

out 

- Ignition distance too high, spark plug

defective

- Carburettor not set correctly

Set or replace spark plug 

Adjust carburetor 

- Air filter dirty

Clean or replace the air filter 

Содержание UBS Easy 13 GE






























Отзывы:

Нет отзывов