KEPCO MST 100-2MHT Скачать руководство пользователя страница 40

Страница: 40 / 42

3-10

MST-MHT SERIES 071320

3.9.2

+5 VOLTS REFERENCE ADJUST (R49)

This procedure establishes the +5V reference voltage used by the analog circuits.

1. Disconnect the load and turn on the UUT. Proceed to step 3 if VOLTAGE MODE indicator is

on.

2. If the CURRENT MODE indicator is on, issue a command from the host computer to set the

UUT to Voltage mode. Verify that VOLTAGE MODE indicator is on.

3. Issue a command from the host computer to reset the UUT. This causes the UUT to be pro-

grammed to zero volts.

4. Connect the voltmeter to test connector J5, pins 1 (REF) and 6 (GND) (see Figure 2-2) and

verify meter reads between 5.00000V ± 500



V volts. If meter reading is outside these limits,

adjust potentiometer R49 for reading of +5.00000V ± 50



3.9.3

OUTPUT VOLTAGE (E

) ZERO ADJUST (R11)

This procedure adjusts the offset of the voltage comparison amplifier to be zero for a pro-
grammed output voltage of zero.

1. Configure DC OUTPUT connector as shown in Figure 3-1 and open S2.

2. With the load disconnected, issue commands from the host computer to enable the output

(output relays closed), e.g.

VOLT 0;CURR 5;:OUTP ON

. Verify OUTPUT ENABLED and

VOLTAGE MODE indicators are on.

3. Connect DVM to DC output connector (see Figure 2-3) pin 5, Sense 1 (+) and pin 2, Sense 2

(–) and verify that output is 0V ± 500



4. If the measured output is outside these limits adjust potentiometer R11 for reading of

0.00000V ± 50



3.9.4

CURRENT SENSE ZERO ADJUST (R50)

This procedure adjusts the current sensing amplifier to zero with no current flowing through the
current sensing resistor.

1. Issue commands (

*RST;:OUTP ON

) from the host computer to reset the UUT.

2. Verify VOLTAGE MODE indicator is on.

3. Connect voltmeter to test connector J5, pins 4 (CSNS - Current Sense) and 6 (GND) and

verify meter reads 0.00000V ± 500



V. If meter reading is outside these limits, adjust potenti-

ometer R50 for 0.00000V ± 50



Содержание MST 100-2MHT











































Результаты поиска

Содержание MST 100-2MHT

Отзывы:

Похожие инструкции для MST 100-2MHT

Бренды по названию

Популярные бренды

KEPCO MST 100-2MHT, Руководство оператора

Результаты поиска

Содержание MST 100-2MHT

Отзывы:

Похожие инструкции для MST 100-2MHT

Бренды по названию

Популярные бренды