Kenwood TS-820 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 11

Kenwood TS-820 Скачать руководство пользователя страница 8

8

1.

Remove resistor R27 (1Kohm) on AF-AVR unit (X49-1080-00).

2.

Install a 10Kohm resistor on foil side of AF-AVR unit. See figure 1.

3.

Install a 1 Kohm resistor on RIT control. See figure 2.

4.

Install a capacitor (3.3uF - 10uF) between RIT control and ground. See figure 2.

5.

Adjust VR-2 on AF-AVR unit (X49-1080-00) for the same frequency as the
center position of the RIT control.

Microphone input attenuator for TS-820

Author:

Trio-Kenwood Communication, inc.

Service bulletin no. 14 (16-2-1977)

When using a high output microphone (i.e. Shure 444), it is very likely that there will be
distortion of the transmitted audio if the processor is used. The reason the distortion
occurs is because the processor is between the first microphone amplifier and the
microphone gain control. The installation of one of the attenuators shown below will
reduce the microphone input to a level that will not cause RF speech processor
distortion. The attenuator figures are approximate.

«
...
6
7
8
9
10
...
»

Содержание TS-820












Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды