background image

20

VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT

When using the optional VGS-1 voice guide &
storage unit, you gain access to the transceiver’s
voice recorder and voice announcement functions.
Ask your dealer for details.

VOICE MEMOS

R

ECORDING

 

A

 V

OICE

 M

EMO

You can record up to 4 voice memos, each with a
duration of up to 15 seconds.  To record a voice
memo for later playback:

1

Press and hold the key programmed as

Playback 1

 to 

4

 for approximately 1 second to

begin recording.  (Each Playback key corresponds
to a memory location of 1 to 4.)

• The duration of recording memory will appear on the

display and begin counting down.  The voice memo
can record only the received signal.

Note:

  Playback keys can be set up for either voice memos or

voice messages by your dealer.  The keys function differently
depending on how they are set up, so be sure to press a
Playback key set up for use for voice memos.

3

Press the 

 key again to confirm the selection and

delete the recording from memory.

• To cancel, press the 

 key.

VOICE MESSAGES

R

ECORDING

 

A

 V

OICE

 M

ESSAGE

You can record up to 4 voice messages, each with a
duration of up to 15 seconds.  To record a voice
message for later playback/transmission:

1

Press and hold the key programmed as

Playback 1

 to 

4

 for approximately 1 second.

(Each Playback key corresponds to a memory
location of 1 to 4).

• “REC/PLAY” appears on the display.

• Press the 

 key to cancel and return to normal

operation.

Note:

  Playback keys can be set up for either voice messages

or voice memos by your dealer.  The keys function differently
depending on how they are set up, so be sure to press a
Playback key set up for use for voice messages.

2

Press the 

 key to end the recording at any time

and store it into the transceiver memory.

• If the memory becomes full, recording will stop

automatically and store the voice memo to memory.

• “WRITING” appears on the display while the

recording is being stored to memory.

P

LAYING

 B

ACK

 

A

 V

OICE

 M

EMO

To play back a recorded voice memo:

1

Press the key programmed as 

Playback 1 

to 

4

 to

play back the specified voice memo.

2

Press the 

 key to end the playback at any time.

D

ELETING

 

A

 V

OICE

 M

EMO

To delete a recorded voice memo:

1

Press the key programmed as 

Playback 1 

to 

4

 to

select and play back the specified voice memo.

2

Press the 

 key to delete the recording.

• “DELETE?” appears on the display.

2

Press the 

 key and speak into the microphone to

begin recording your message.

• The duration of recording memory will appear on the

display and begin counting down.

3

Press the 

 key to end the recording at any time

and store it into the transceiver memory.

• If the memory becomes full, recording will stop

automatically and store the voice message to
memory.

• “WRITING” appears on the display while the

recording is being stored to memory.

Содержание TK-90



























Отзывы: