background image

v

i

nformaTion

 

concerning

 

The

 

baTTerY

 

Pack

The battery pack ncludes flammable objects such as organc solvent.  

Mshandlng may cause the battery to rupture producng flames or 

extreme heat, deterorate, or cause other forms of damage to the 

battery.  Please observe the followng prohbtve matters.

• 

Do not disassemble or reconstruct battery!

 

The battery pack has a safety functon and protecton crcut to 

avod danger.  If they suffer serous damage, the battery may 

generate heat or smoke, rupture, or burst nto flame.

• 

Do not short-circuit the battery!

 

Do not jon the + and – termnals usng any form of metal (such 

as a paper clp or wre).  Do not carry or store the battery pack 

n contaners holdng metal objects (such as wres, chan-

necklace or harpns).  If the battery pack s short-crcuted, 

excessve current wll flow and the battery may generate heat 

or smoke, rupture, or burst nto flame.  It wll also cause metal 

objects to heat up.

• 

Do not incinerate or apply heat to the battery!

 

If the nsulator s melted, the gas release vent or safety functon 

s damaged, or the electrolyte s gnted, the battery may 

generate heat or smoke, rupture, or burst nto flame.

• 

Do not use or leave the battery near fires, stoves, or other 

heat generators (areas reaching over 80°C/ 176°F)!

 

If the polymer separator s melted due to hgh temperature, 

an nternal short-crcut may occur n the ndvdual cells and 

the battery may generate heat or smoke, rupture, or burst nto 

flame.  

• 

Avoid immersing the battery in water or getting it wet by 

other means!

 

If the battery becomes wet, wpe t off wth a dry towel before 

use.  If the battery’s protecton crcut s damaged, the battery 

may charge at extreme current (or voltage) and an abnormal 

chemcal reacton may occur.  The battery may generate heat or 

smoke, rupture, or burst nto flame.

Содержание TK-5220













































Отзывы: