Kenwood TK-190 Скачать руководство пользователя страница 2

Страница: 2 / 32

◆

GOVERNMENT LAW PROHIBITS THE OPERATION OF

UNLICENSED RADIO TRANSMITTERS WITHIN THE

TERRITORIES UNDER GOVERNMENT CONTROL.

◆

ILLEGAL OPERATION IS PUNISHABLE BY FINE OR

IMPRISONMENT OR BOTH.

◆

REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.

◆

DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE

ATMOSPHERES (GASES, DUST, FUMES, ETC.).

◆

TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL,

OR WHILE PARKED IN GASOLINE SERVICE STATIONS.

THANK YOU

We are grateful you chose

KENWOOD

for your land

mobile radio applications. We believe this easy-to-use

transceiver will provide dependable communications to

keep personnel operating at peak efficiency.

KENWOOD

transceivers incorporate the latest in

advanced technology. As a result, we feel strongly that

you will be pleased with the quality and features of this

product.

NOTICES TO THE USER

SAFETY

: It is important that the operator is aware of

and understands hazards common to the operation of

any transceiver.

PERFORMANCE

: The performance of low band

portable transceiver depends on your operating practices

and the environmental conditions. To obtain the best

performance from your transceiver, use the transceiver

only with a KRA-21 antenna. Refer to the KRA-21

instruction manual for important information concerning

the use of the antenna.

Содержание TK-190

































Результаты поиска

Содержание TK-190

Отзывы:

Похожие инструкции для TK-190

Бренды по названию

Популярные бренды

Kenwood TK-190, Инструкция по эксплуатации

Результаты поиска

Содержание TK-190

Отзывы:

Похожие инструкции для TK-190

Бренды по названию

Популярные бренды