Kenwood NX-5900 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 120

background image

1-22 (No.RA032<Rev.001>)

2.4.8 Signaling Circuit
2.4.8.1

Encode (QT/DQT/DTMF/2-tone/MSK)

Each signaling data signal of QT, DQT, DTMF, 2-tone and MSK is generated by IC706, superposed on a modulation signal and output
to TX VCO and PLL IC.

2.4.8.2

Decode (QT/DQT/DTMF/2-tone/MSK)

The audio signal is removed from the FM detection signal sent to the IC706 and the resulting signal is decoded by IC706.

2.4.9 Bluetooth/GPS Circuit

The main component of the Bluetooth/GPS circuit is Bluetooth / GPS IC (IC5) on MODULE unit.
The clocks of Bluetooth/GPS IC require 19.2MHz for core and 32.768kHz slow clock (X1 and X2) for UART.
Bluetooth/GPS IC communicates to the OMAP processor (IC706) on the HCI UART. Interface of UART & Digital audio (PCM) between
the OMAP processor (IC706) and the Bluetooth/GPS IC (IC5), have level conversion at the level shift IC (IC6 and IC7) on MODULE
unit.The Bluetooth/GPS IC is powered by 1.8V and 3.3V which are supplied from 2 discrete external regulators (IC2 and IC3) on MOD-
ULE unit.

Fig.5 Bluetooth/GPS circuit

2.4.9.1

Bluetooth Circuit

The Bluetooth / GPS IC (IC5) support Bluetooth 3.0 up to HCI level.
TX/RX frequency is 2400-2483.5MHz (79ch Hopping, 2402-2480MHz, 1MHz step). Transmitting power is +2dBm at Bluetooth anten-
na input.
Using the printed antenna with Bluetooth, and connected to the Bluetooth / GPS IC (IC5) through the saw filter (L11).
Frequency configuration for Bluetooth is following:
There are two LO modes: 2X and Offset LO (OSLO). 2X where LO is 2*RF_FREQ (e.g. when transmitting at 2441MHz it is at
4882MHz). OSLO where LO is at (2/3)*RF_FREQ (e.g. when transmitting at 2441MHz it is at 1627.333MHz).
In RX the 2X is always used.
In GFSK TX if power is >10dBm then OSLO is used
In EDR2 TX if power is >-12dBm then OSLO is used
In EDR3 TX if power is >-12dBm then OSLO is used
Otherwise 2X is used for TX as well.

2.4.9.2

GPS Circuit

The GPS RF signal is received with the active antenna, and connected to the Bluetooth / GPS IC (IC5) through the terminal (CN5)
and saw filter (L9).
The output is passed to pin L2 of the GPS IC. The input match for pin L2 comprises of C38, C36 and L7.
The control and data lines for the GPS IC are GPS_PA_EN, BTFM_nSHUTDOWN, GPS_TX and GPS_RX.
GPS_TX and GPS_RX are shared with Bluetooth data line.
Frequency configuration for GPS is following: Lo is GPS: 1571.324MHz

Fig.6 GPS circuit

IC706

IC6

IC5

UART

UART

UART

IC7

PCM

PCM

PCM

X1

X2

CN5

BT/GPS IC

TCXO
19.2MHz

32.768kHz
Clock

BPF

Bluetooth
antenna

Level
shift IC

Level
shift IC

BPF

GPS

antenna
connector

Module (BT/GPS) unit

Main unit

MPU/DSP

BPF

GPS

antenna

TCXO

19.2MHz

MPU/DSP

1.8V

3.3V

GPS_LNA_IN(L2)

TCXO_CLK_LV(F1)

BT_HCI_UART_TX(A4)

BT_HCI_UART_RX(B5)

RTC_CLK(H9)

OSCILLATOR

32.768kHz

BTFM_nSHUTDOWN(A6)

GPS_PA_EN(G3)

VBAT1(A2)

LEVEL
SHIFT

TCXO_LDO_IN(H1)

VDDS

GPS TX

GPS_RX

BT

antenna

BT_RF

BT/GPS IC

Antenna
connector

BPF

GPS ANT ALM

GPS ANT PWR

GPS

detect

3.3V

33GPS

33BT

18BT

IC706

«
...
20
21
22
23
24
...
»

Содержание NX-5900

























































































































Отзывы:

Нет отзывов

Похожие инструкции для NX-5900

Бренд: DigiTech Страницы: 4

DDR-63 - WIFI INTERNET RADIO-TUNERS

Бренд: Sangean Страницы: 1

Бренд: tez audio Страницы: 4

Бренд: Dataradio Страницы: 35

Бренд: Campbell Страницы: 51

Бренд: Albrecht Страницы: 23

Бренд: Sangean Страницы: 27

Бренд: Yaesu Страницы: 88

Бренд: Ericsson GE Страницы: 16

Бренд: La Crosse Technology Страницы: 22

HomePatrol - II

Бренд: Uniden Страницы: 43

Бренд: PURE Страницы: 88

Бренд: COP-USA Страницы: 11

Бренд: GME Страницы: 28

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 12

Бренд: Philips Страницы: 13

Бренд: Philips Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды