manualshive.com logo in svg

Kenwood NEXEDGE NX-410, Инструкция по эксплуатации

Поделиться
Скачать
Kenwood NEXEDGE NX-410 Скачать руководство пользователя страница 16

3

Do not use glue which is designed to prevent screw loosening when 
installing the belt clip.  Acrylic ester, which is contained in these 
glues, may crack the transceiver’s back panel.

I

NSTALLING

 

THE

 C

AP

 

OVER

 

THE

 U

NIVERSAL

 C

ONNECTOR

I

NSTALLING

 

THE

 B

ELT

 C

LIP

Attach the belt clip using the 
supplied 3 x 8 mm screws.

Note:

  If the belt clip is not 

installed, its mounting location 
may get hot during continuous 
transmission or when left sitting in 
a hot environment.

Insert the cap into place over the 
universal connector and secure 
it in place using the attached 
screw.

I

NSTALLING

 

THE

 (O

PTIONAL

) S

PEAKER

/ M

ICROPHONE

 

OR

 H

EADSET

1

  Insert the guide of the 

speaker/ microphone or 
headset connector into place 
over the universal connector.

2

  Secure the connector in place 

using the attached screw.

Note:

  When not using an optional 

speaker/ microphone or headset, 
install the cap over the universal 
connector.

3 x 8 mm screws

Belt clip

MIC

Optional

speaker/ microphone

MIC

Universal

connector cap

Содержание NEXEDGE NX-410













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды