Kenwood NEXEDGE NX-300 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 10

background image

NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4

FCC ID: ALH378501

IC: 282D-378501

Installing the Antenna

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and
turning it clockwise until secure.

Installing the Belt Clip

If necessary, attach the belt clip using the two supplied 3 x 6 mm screws.

Notes:

If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting

in a hot environment.

«
...
2
3
4
5
6
...
»

Содержание NEXEDGE NX-300











Отзывы:

Нет отзывов

Похожие инструкции для NEXEDGE NX-300

Бренд: TDK Страницы: 3

Бренд: Marquant Страницы: 12

Бренд: Briggs & Stratton Страницы: 7

Бренд: Ferguson Страницы: 21

Бренд: Sandstrom Страницы: 36

Бренд: HanRongDa Страницы: 16

Бренд: Bush Страницы: 24

Бренд: auna multimedia Страницы: 24

Бренд: Linden Страницы: 28

Бренд: Cobra Страницы: 11

Бренд: NXP Semiconductors Страницы: 2

Storm Responder 5500

Бренд: Briggs & Stratton Страницы: 48

Бренд: Baofeng Страницы: 22

Бренд: GPX Страницы: 12

Бренд: LENCO Страницы: 31

Бренд: ASCO POWER TECHNOLOGIES Страницы: 18

Бренд: Digi Страницы: 67

Бренд: Rockpals Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды