KRC-Z965,X838
9
• HPF is adjusted in 2 steps of Through / 220Hz with the
Track Up/Down keys.
• LPF is adjusted in 2 steps of Through / 120Hz with the
Track Up/Down keys.
• Bass f, Bass Q, Bass EXT, Middle f, Middle Q and Treble
f are not dealt with by the audio adjust.
7. Menu-related specifications
• Pressing the DNPP/SBF key on the remote initiates the
Menu mode.
• Continuous holding of a remote control key is inhibited.
• In the case of the cassette receiver model, A short press
of the TI key initiates the Menu mode.
8. Backup current measurement
When the unit is reset while ACC is OFF (i.e. by turning
Backup ON), the MUTE terminal goes OFF in 2 seconds in
place of 15 second. (The CD mechanism is not activated at
this time.)
9. Special display when the display is all on
Pressing the Preset keys while the power is ALL OFF
displays the following information.
PRESET 1
Version display (8 digits, Month/Day/Hour/Minute)
(Display) SYS xxxxxxxx : System microcomputer
PAN xxxxxxxx : Panel microcomputer
PRESET 2
Sireal number display (8 digits)
(Display) SNo xxxxxxxx
z
PRESET 3
Short press : View power ON time.
(The All OFF period is not counted.)
Long press/hold : Clear power ON time at
the power ON time displaying.
(Display) PON xxxxx
Max. 65535 (hours)
PRESET 4
Short press : Display TAPE operation time.
Long press/hold : Clear TAPE operation time
at the TAPE operation time displaying.
(Display) TapTim xxxxx Max. 65535 (hours)
PRESET 5
Short press : Display TAPE ejection count.
Long press/hold : Clear TAPE ejection count
at the TAPE ejection count displaying.
(Display) EjeCnt xxxxx Max. 65535 (times)
PRESET 6
Short press : Display Panel open/close count.
Long press/hold : Clear Panel open/close
count at the Panel open/close count.
(Display) PnCnt xxxxxx Max. 655350 (times)
TEST MODE
1. How to enter the test mode
While pressing and holding the Preset 1 and Preset 3 keys,
reset the unit.
2. How to exit from the test mode
Reset the unit, ACC OFF, power OFF and Panel detached.
(Note) The test mode cannot be terminated by momentary
power down.
3. Initial status in the test mode
• Sources
: ALL OFF
• Display
: All segments are lit.
• Volume
: –10 dB (displayed as "30")
• Loudness
: OFF
• CRSC
: OFF regardless of the presence of
switching function.
• SYSTEM Q
: Flat
• BEEP
: When pressing any keys, the buzzer
generates a beep at any time.
4. Special display in Tuner mode
When any of the following messages is displayed in Tuner
mode, the F/E may be abnormal.
• "TNE2P NG": The EEPROM is set to the default (unstable
values) because the F/E was shipped without passing
through the adjustment process, etc.
• "TNCON NG": Communication with the F/E is not
possible.
5. Forced switching of K3I
Each press of the Preset 6 key in Tuner mode should switch
K3I from AUTO
→
Forced Wide
→
Forced Middle
→
Forced
Narrow
→
AUTO.
The initial status is AUTO and the display shows these
modes as follows.
• AUTO
6. Audio-related specifications
• A short press of the Q key initiates the audio adjustment
• Pressing the
∗
key on the remote initiates the audio
adjustment mode.
• Fader is selected to the initial item.
• Continuous holding of a remote control key is inhibited.
• Bass, Middle and Treble are adjusted in 3 steps of Min /
Center / Max with the Track Up/Down keys.
• Balance is adjusted in 3 steps of Left Max / Center / Right
Max with the Track Up/Down keys.
• Fader is adjusted in 3 steps of Rear Max / Center / Front
Max with the Track Up/Down keys.
10. Method of the span switching (K and M type only)
While pressing and holding the Preset 1 and Preset 5 keys,
reset the unit.
11. Other specifications
• No displays such as " CODE OFF " during Power ON.
• Pressing the TI (AUTO) key during changer operation
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
