Kenwood KRC-266LG, Инструкция по эксплуатации

Страница: 28 / 64

English
— 28 —
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
General
?
The power does not turn ON. 01
✔
The fuse has blown.
☞
After checking for short circuits in the wires, replace the fuse with
one with the same rating.
✔
No ACC position on vehicle ignition. 02
☞
Connect the same cable to the ignition as the battery cable.
?
Nothing happens when the buttons are pressed. 04
✔
The computer chip in the unit is not functioning normally.
☞
Press the reset button on the unit (page 4).
?
There’s a source you can’t switch. 05
✔
There’s no tape inserted.
☞
Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
?
There’s a source you can’t switch. 07
✔
The Disc changer isn’t connected. 08
☞
Connect the Disc changer. If the Disc changer isn’t connected to
it's input terminal, You can't switch to an external disc source.
?
The faceplate does not open or close. 09
✔
The faceplate is incorrectly attached.
☞
Reattach the faceplate correctly, See the section on <Removing
the Faceplate>(page 8).
?
The memory is erased when the ignition is turned OFF. 10
✔
The battery wire has not been connected to the proper terminal.
☞
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
✔
The ignition and battery wire are incorrectly connected. 11
☞
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
?
The TEL mute function does not work. 15
✔
The TEL mute wire is not connected properly.
☞
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
?
The TEL mute function turns ON even though the TEL mute wire is
not connected.
16
✔
The TEL mute wire is touching a metal part of the car.
☞
Pull the TEL mute wire away from the metal part of the car.
?
Even if Loudness is turned ON, high-pitched tone isn't compensated
for.
17
✔
Tuner source is selected.
☞
High-pitched tone isn't compensated for when in Tuner source.
?
No sound can be heard, or the volume is low.
✔
The fader or balance settings are set all the way to one side. 21
☞
Center the fader and balance settings.
✔
The input/output wires or wiring harness are connected incorrectly. 22
☞
Reconnect the input/output wires or the wiring harness correctly.
See the section on "Connecting Wires to Terminals".
✔
The cassette tape is bad. 23
☞
Try playing another cassette tape. If works fine, the first tape was
bad.
?
The sound quality is poor or distorted. 25
✔
One of the speaker wires is being pinched by a screw in the car.
☞
Check the speaker wiring.
✔
The tape head is dirty. 26
☞
Clean the tape head.
✔
The speakers are not wired correctly. 27
☞
Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
?
The Touch Sensor Tone doesn’t sound. 34
✔
The preout jack is being used.
☞
The Touch Sensor Tone can’t be output from the preout jack.
?
Even though Synchronize Clock is ON, the clock can’t be adjusted. 35
✔
The received RDS station isn’t sending time data.
☞
Receive another RDS station.
Troubleshooting Guide
— 28 —
KRC-266R_266L(M_E)_U.S_r1 02.9.25 1:40 PM Page 28