Kenwood KIV-700, Инструкция по эксплуатации

Страница: 80 / 84

80
|
KIV-BT900/ KIV-700
Troubleshooting Guide
Hands-free
?
The hands-free talk volume is low.
 The hands-free talk volume is set at a low level.
 The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“Mic Gain” and “Noise Reduction”
<Bluetooth
Setting> (page 50) .
?
No sound is heard from the rear speakers.

You are talking in the hand-free talk mode.

No sound is heard from the rear speakers in the
hands-free talk mode.
?
No beep is heard at reception of an incoming call.
 No beep is heard depending on the type of your
cell-phone.
 The “Call Beep” of <Bluetooth Setting> (page 50) is
set ON.
?
Voice is not recognized.

The vehicle window is open.

If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.

Small voice.

If voice is too small, it cannot be recognized
properly. Speak into the microphone a little more
loudly and naturally.

The person uttering the voice tag is not the one who
registered the it.

Only the voice of the person who registered the
voice tag can be recognized.
Bluetooth audio source
?
The Bluetooth audio player cannot be registered
(pairing).

The PIN code is fixed.

When a PIN code is specified in the Instruction
Manual for Bluetooth Audio Player, register it
with reference to
<Registering PIN Code> (page
52) to register the Bluetooth audio player. If no PIN
code is specified in the Instruction Manual, try
“0000”.
?
The sound from the Bluetooth audio player is
discontinuous.

The distance between this unit and audio player is
too far.

Move the audio player nearer to this unit.

Another Bluetooth device is affecting the Bluetooth
communication.

Turn off another Bluetooth device.

Move another Bluetooth device away from this
unit.

Another Bluetooth device or profile is used for
communication.

The downloading of the Phone book or the SMS
disconnects the sound.
The messages shown below display your
systems condition.
TOC Error: • No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
Error 05: The disc is unreadable.
Error 77: The unit is malfunctioning for some reason.

Press the reset button on the unit. If the
“Error 77” code does not disappear, consult
your nearest service center.
Error 99: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
 Check the disc magazine. And then press
the reset button on the unit. If the “Error
99” code does not disappear, consult your
nearest service center.
Protect (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.

Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
Unsupported File:
An Audio file is played with a format that this
unit can’t support.
Copy Protection:
A copy-protected file is played.
Read Error: The file system of the connected USB device
is broken.
 Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
No Device: The USB device is selected as a source
although no USB device is connected.

Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
N/A Device: • An unsupported USB device is connected.
• Connection to the iPod has failed.
 Check that the connected iPod is an iPod
that is supported. See <iPod/iPhone that
can be connected to this unit> (page 66) for
information on supported iPods.
No Media File/Error 15:
• The connected USB device contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.