— 36 —
English
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
?
The power does not turn ON.
01
✔
The fuse has blown.
☞
After checking for short circuits in the wires, replace the fuse with
one with the same rating.
✔
No ACC position on vehicle ignition.
02
☞
Connect the same wire to the ignition as the battery wire.
✔
The remote controller does not work.
☞
See <Connecting Wires to Terminals> (page 30) to connect the
light detector of the remote controller correctly.
?
The power cannot be turned off
✔
You select the source mode of this machine, which is connected to a
center unit.
☞
The power cannot be turned off because the center unit is under
operation. If changing a mode other than the source mode of this
machine on the center unit, you can turn off the power.
?
The power is automatically turned off.
✔
You switched the source mode while connecting to a center unit.
☞
If selecting the source mode of this machine on the center unit
and then switching to a mode other than this machine, you can
turn off the power.
?
No video image appears.
✔
The unit is not connected to the parking brake detection switch.
☞
Make proper connections according to <Connecting Wires to
Terminals>.
✔
The parking brake is not engaged.
☞
For safety reasons no video images are displayed while the
vehicle is moving. Engaging the parking brake will cause images
to be displayed.
✔
The setting of the NTSC/PAL switch is incorrect.
☞
Set the NTSC/PAL switch correctly.
?
Nothing happens when the buttons are pressed.
04
✔
The "
" symbol appears in the screen.
☞
You cannot carry out any operation disabled by disc.
✔
The batteries of the remote controller are weak.
☞
Replace both two batteries of the remote controller with new
ones.
✔
The remote controller does not work.
☞
See <Connecting Wires to Terminals> to connect the light
detector of the remote controller correctly.
✔
A center unit not applicable is connected.
☞
See <IMPORTANT INFORMATION> (page 4).
?
The memory is erased when the ignition is turned OFF.
10
✔
The battery wire has not been connected to the proper terminal.
☞
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
✔
The ignition and battery wire are incorrectly connected.
11
☞
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
?
No sound can be heard, or the volume is low.
✔
The audio setting of audio output is not “ANALOG”.
☞
If connecting through a center unit or RCA cable, select
“ANALOG” for this setting.
✔
The input/output wires or wiring harness are connected incorrectly.
22
☞
Reconnect the input/output wires or the wiring harness correctly.
See the section on <Connecting Wires to Terminals>.
?
The specified disc does not play, but another one plays instead.
52
✔
The specified DVD/CD is quite dirty.
☞
Clean the Disc.
✔
The disc is upside down.
☞
Set the disc with the label face downward.
✔
The disc is severely scratched.
55
☞
Try another disc instead.
?
The specified track will not play.
58-a
✔
Random play has been selected.
☞
Turn off random play.
?
Cannot play CD-R or CD-RW.
60
✔
Finalization processing is not being conducted for CD-R/CD-RW.
☞
Conduct finalization processing with CD recorder.
?
A VCD cannot be played using menus.
✔
The VCD disc being played is not compatible with P.B.C.
☞
Menu playback is available only with VCD discs recorded with
P.B.C.
Troubleshooting Guide
KDV-C810_U.S_r02 02.12.16 12:53 PM Page 36