Kenwood KDC-8026 Скачать руководство пользователя страница 36

Страница: 36 / 40

English

Troubleshooting Guide

What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.

General

The power does not turn ON.

✔

The fuse has blown.

☞

After checking for short circuits in the wires,

replace the fuse with one with the same
rating.

✔

Speaker cable touches on chassis etc.

☞

Wire or insulate the speaker cable properly

and press the reset button.

✔

The Demonstration mode has been selected.

☞

Hold down button [5] and press the Reset

button to release the Demonstration mode.

There’s a source you can’t switch.

✔

There’s no media inserted.

☞

Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each
source.

✔

The Disc changer isn’t connected.

☞

Connect the Disc changer. If the Disc changer

isn’t connected to it’s input terminal, You can’t
switch to an external disc source.

The memory is erased when the ignition is

turned OFF.

✔

The ignition and battery wire are incorrectly

connected.

☞

Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.

There’s no loudness effect.

✔

You’re using Subwoofer preout.

☞

Loudness has no effect in Subwoofer preout.

The TEL mute function does not work.

✔

The TEL mute wire is not connected properly.

☞

Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.

The TEL mute function turns ON even though the

TEL mute wire is not connected.

✔

The TEL mute wire is touching a metal part of the

car.

☞

Pull the TEL mute wire away from the metal

part of the car.

Even if Loudness is turned ON, high-pitched tone

isn’t compensated for.

✔

Tuner source is selected.

☞

High-pitched tone isn’t compensated for when

in Tuner source.

No sound can be heard, or the volume is low.

✔

The fader or balance settings are set all the way to

one side.

☞

Center the fader and balance settings.

✔

The input/output wires or wiring harness are

connected incorrectly.

☞

Reconnect the input/output wires or the

wiring harness correctly. See the section on
'Connecting Wires to Terminals'.

✔

The values of Volume offset are low.

☞

Turn up the Volume offset, referring to the

section on 'Audio Control' (page 12).

✔

The 'Built-in Amp Mute Setting' (page 27) is ON.

☞

Turn it OFF.

The sound quality is poor or distorted.

✔

One of the speaker wires is being pinched by a

screw in the car.

☞

Check the speaker wiring.

✔

The speakers are not wired correctly.

☞

Reconnect the speaker wires so that each

output terminal is connected to a different
speaker.

The Touch Sensor Tone doesn’t sound.

✔

The preout jack is being used.

☞

The Touch Sensor Tone can’t be output from

the preout jack.

The Dimmer function doesn’t work.

✔

The Dimmer wire isn’t connected correctly.

☞

Check the Dimmer wire connection.

The panel is not hidden even when the power is

turned off.

✔

The protection function for preventing fingers or

other things from getting caught in between the
panel and this unit has been activated.

☞

Turn off the power again.

The Control Panel moves although you do not

desire.

✔

The Demonstration mode has been selected.

☞

Hold down button [5] and press the Reset

button to release the Demonstration mode.

B64-2745-00̲U.S(M).Indd 36

03.11.27, 3:27:13 PM

Содержание KDC-8026









































Результаты поиска

Содержание KDC-8026

Отзывы:

Похожие инструкции для KDC-8026

Бренды по названию

Популярные бренды

Kenwood KDC-8026, Инструкция по эксплуатации

Результаты поиска

Содержание KDC-8026

Отзывы:

Похожие инструкции для KDC-8026

Бренды по названию

Популярные бренды