manualshive.com logo in svg

Kenwood KDC-3051M, Инструкция по эксплуатации

Поделиться
Скачать
Kenwood KDC-3051M Скачать руководство пользователя страница 13

13

ENGLISH

Installation/connection

Part list:

A

 Faceplate.............................................................. (×1)

B

 Escutcheon ......................................................... (×1)

C

 Mounting sleeve ............................................. (×1)

D

  Casing for faceplate ......................................  (×1)

E

 Wiring harness 

.................................................. (×1)

F

 Removal tool ..................................................... (×2)

KDC-MP249/ KDC-MP2049/ KDC-MP149 only:

G

  Flat head screw (for Nissan cars) ...........  (×4)

H

  Round head screw (for Toyota cars) ....  (×4)

Basic procedure

1 

Remove the key from the ignition 
switch, then disconnect the 

·

 terminal 

of the car battery.

2 

Make proper input and output wire 
connections.

 

\

 “Wiring connection” (page 14)

3 

Install the unit to your car.

 

\

 “Installing the unit” (page 15)

4 

Reconnect the 

·

 terminal of the car 

battery.

5 

Reset the unit. (page 3)

Warning

 The unit can only be installed in a car with 

a 12 V DC power supply, negative ground.

 If you connect the ignition wire (red) and 

the battery wire (yellow) to the car chassis 
(ground), you may cause a short circuit, 
that in turn may start a fire. Always connect 
those wires to the power source running 
through the fuse box.

 Disconnect the battery's negative terminal 

and make all electrical connections before 
installing the unit.

 Insulate unconnected wires with vinyl tape 

or other similar material. To prevent a short 
circuit, do not remove the caps on the ends 
of the unconnected wires or the terminals.

 Be sure to ground this unit to the car's 

chassis again after installation.

Caution

 If your car's ignition does not have an ACC 

position, connect the ignition wires to a 
power source that can be turned on and 
off with the ignition key. If you connect 
the ignition wire to a power source with 
a constant voltage supply, as with battery 
wires, the battery may die.

 Do not use your own screws. Use only the 

screws provided.

 Install this unit in the console of your 

vehicle. Make sure the faceplate will not hit 
the lid of the console (if any) when closing 
and opening.

 After the unit is installed, check whether 

the brake lamps, blinkers, wipers, etc. on 
the car are working properly.

 Mount the unit so that the mounting angle 

is 30° or less.

 If the fuse blows, first make sure the wires 

aren't touching to cause a short circuit, 
then replace the old fuse with one with the 
same rating.

 Connect the speaker wires correctly to the 

terminals to which they correspond. The 
unit may be damaged or fail to work if you 
share the 

·

 wires or ground them to any 

metal part in the car.

 When only two speakers are being 

connected to the system, connect the 
connectors either to both the front output 
terminals or to both the rear output 
terminals (do not mix front and rear).

 Do not touch the metal part of this unit 

during and shortly after the use of the 
unit. Metal part such as the heat sink and 
enclosure become hot.

 Mounting and wiring this product requires 

skills and experience. For safety's sake, leave 
this work to professionals.

  If you experience problems during 

installation, consult your Kenwood dealer.

EN02-15_KDC-MP249[M]f.indd   13

EN02-15_KDC-MP249[M]f.indd   13

8/10/10   10:23:57 AM

8/10/10   10:23:57 AM

Содержание KDC-3051M
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды