background image

VIBRATE FUNCTION

With press the Menu key and Up key for (0.5) seconds to appear the Vibrate Icon on the
LCD with BEEP2. The Vibrate function will be operated as follows.

l_

Receiving (After Carrier Detect for (1) second) at the FRS Mode

 Vibration for (1) second and stop for (0.5) seconds repeat three times

after then will be in the stand by until next receiving.

VIBRATE MODE RELEASING

l_

Transmission

l_

Monitor Operation

l_

Call Operation

l_

With press the Menu Button and Down

NOTICES TO USER

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

• 

Consult the dealer for technical assistance.

SAFETY INFORMATION

Your wireless hand-held portable transceiver contains a low power transmitter. When the Push-to-
Talk (PTT) button is pushed it sends out radio frequency (RF) signals. The device is authorized to
operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications
Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held
wireless devices.

CAUTION

: To maintain compliance with the FCC's RF exposure guidelines hold the transmitter and

antenna at least 2 inch (5 centimeters) from your face and speak in a normal voice, with the
antenna pointed up and away from the face. If you wear the handset on your body while using the
headset
accessory, use only the Kenwood supplied belt clip for this product and when transmitting, take it
out of the belt to ensure that the antenna is at least 1 inch (2.5 centimeters) from your body.
Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage
the transmitter and may violate FCC regulations.

                        

LIMITED WARRANTY STATEMENT

Kenwood Communications Corporation (“KENWOOD”) warrants this product for
ninety (90) days on parts and labor, measured from the date of purchase by the first
end user.

 

This Warranty is enforceable only by the first end user.

Except as specified below, this w arranty covers all defects in material and
workmanship in this product.  The following are not covered by the Warranty:
1.

Damage, deterioration or failure resulting from:
A. Accident, misuse, abuse, neglect, product modification or failure to follow

Instructions contained in your Owner’s Manual.

B. Repair or attempted repair by anyone not authorized by KENWOOD.
C. Installation of parts that do not conform to the quality or specifications of the

original parts.

2.

Damage or loss occurring during shipment (claims must be presented to the

Содержание FreeTalk WX UBZ-GM14

Страница 1: ...WITH ALKALINE CELLS RATIO OF TRANSMISSION RECEPTION AND STAND BY PERIODS IS 1 1 8 CONTROL DIAGRAM INSTALLING REMOVING BATTERY This transceiver requires 3 AA batteries Use high quality alkaline batteries to enjoy longer periods of battery life An audible warning beep is generated when battery level is very low Reception is still enabled but battery replacement is required 1 Release the battery cove...

Страница 2: ...ing pressing the Monitor key Audio is On and RX Icon appears on the LCD Release the key to return to Stand by Mode and Audio will be muted l_ Continuous Monitor Mode Press the Monitor key for more than 3 seconds Monitor Mode will be operated with Single Beep RX Icon appears on the LCD BACK LIGHT ON OFF When any key is pressed the LCD will be illuminated The lamp will be out after 5 seconds BATTERY...

Страница 3: ...ct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer for technical assistance SAFETY INFORMATION Your wireless hand held portable transceiver contains a low power trans...

Страница 4: ...ITNESS FOR A PARTICULAR PURPOSE HEREBY ARE EXCLUDED B KENWOOD S LIABILITY UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT AT KENWOOD S OPTION OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE DAMAGES OF ANY KIND WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE This Warranty is enforceable only in the United States of America If a problem develops during or after the Limited Warranty Pe...

Отзывы: