Kenwood DT-7000S - Sirius Satellite Radio Tuner, Инструкция по эксплуатации

Страница: 10 / 16

4. When one (or more) of the selected songs is playing on any stream, an alert screen will be
superimposed over the data on the original screen ( below ).
• The number on the screen will
count down from ‘10’ to ‘0’.
To hear the song, press the ENTER
button before the counter reaches
zero; to make the alert screen dis-
appear, press the SETUP button on
the front panel. The DT-7000S will
switch to the stream that is playing
the song.
• If you do nothing, the alert screen will disappear when the counter reaches zero.
Display options
Changing display modes
The Normal Operation Screen has two
modes, Normal and Large Font ( right ).
Press the DISPLAY button to cycle the
display between the two modes.
Adjusting the display brightness
• Press the DIMMER button on the
remote to cycle the display through
the three brightness levels
(high/medium/low).
Setup Mode
The Setup Mode lets you access and
set up the following features: SID (SIRIUS ID Number), Clock, Alarm, Channel Skip/Lock,
Lock Code Setup, Auto Shutoff, Startup Mode, Output Level, Antenna Signal and Preset
Bank Naming.
To enter the Setup Mode, press the SETUP button.
SID
When you first enter the Setup Mode,
the unit’s unique 12-digit SIRIUS ID
Number will be displayed ( right ):
Clock Setup
The DT-7000S has an automatic clock
that receives its time signal as part of
the SIRIUS satellite stream.
To set the clock, you need to tell the DT-7000S what time zone you live in and if your
local area observes Daylight Savings Time.
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Auto
Clock Setup screen appears ( right ).
2. Turn the CH/PRESET jog dial (unit)
or press the CH buttons (remote)
once and the Time Zone Setup
screen appears ( middle, right ).
3. Turn the CH/PRESET jog dial (unit)
or press the CH buttons (remote)
until your time zone is highlighted,
then press the ENTER button.
• The screen will change to the Daylight
Savings screen ( below, right ).
3. If your local area observes Daylight
Savings Time, press the ENTER
button so an “X” appears in the box
on the display’s fourth line; if your
local area does not observe Daylight
Savings Time, press the ENTER but-
ton so that the box is empty.
Press the SETUP button to exit.
Timer Functions
The DT-7000S has three Timer functions. The Alarm turns the DT-7000S on at a
specified time and to a specified stream, Auto Shut-Off automatically turns it off at a
specified time, and the Sleep Timer lets you listen to the DT-7000S for a specified peri-
od of time before it automatically shuts off.
Setting the Alarm
1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Alarm
Clock Setup screen appears ( right ).
2. Turn the CH/PRESET jog dial (unit)
or press the CH buttons (remote).
The Step 1 — Set Alarm Time screen
appears ( lower, right ).
3. Use the CH/PRESET jog dial (unit)
or press the CH buttons (remote) to
set the hour you want the DT-7000S
to turn on. (The alarm will auto-
matically switch from AM to PM.)
4. When the display shows the correct hour, turn the CATEGORY jog dial (unit) or press
the CAT buttons (remote) to highlight the minutes. Use the CH/PRESET jog dial (unit)
or press the CH buttons (remote) to set the minute you want the DT-7000S to turn on.
DT-7000S Instruction Manual
10
Song Seek Alert Screen
Normal Operation Screen
Large Font Screen
SIRIUS ID Screen
Time Zone Setup Screen
Daylight Savings Screen
Auto Clock Setup Screen
Alarm Setup Screen
Step 1—Set Alarm Time Screen