![Kenwood ddx712 - DVD Player With LCD monitor Скачать руководство пользователя страница 30](http://html.mh-extra.com/html/kenwood/ddx712-dvd-player-with-lcd-monitor/ddx712-dvd-player-with-lcd-monitor_service-manual_187094030.webp)
30
DDX7032/7032M/712
DNX7120/7220/7320
Cancel
Return
Parrot Check
Parrot Check
E
Parrot Check
Parrot OK/NG
Figure 4.14 Parrot Check screen
Key Speci
fi
cation
Parrot Check : Start Parrot check.
Cancel
: Transfer to Test Mode Main screen.
Return
: Transfer to Test Mode Main screen.
5. Functional speci
fi
cation
This section describes the test mode speci
fi
cation in each
function.
5.1. Display
In the Test mode, the display is exclusively used for the test
but screens for Source Control, Audio Control and Setup
are same as those that are normally used.
The system shows the touch position (+). However, it is not
shown in the Touch Adjust screen (under adjustment).
5.2. Key
The hard key speci
fi
cation is listed in Table 5.2. (Note that
the keys that are not listed in the table have conventional
functions.)
Key
Function
ATT
Motor driver
Table 5.2 Hard key
Mode Description
Setting
Test Mode
SRC+ATT+Reset
Span switching
SRC + VOL.DW + Reset
DC Offset/Service/Memory Other Clear SRC+FNC+Reset
Retailer mode: ON
EJECT + VOL.DW + Reset
Retailer mode: OFF
SRC+Reset
RDS test drive mode
EJECT+ATT+Reset
Opening screen re-write mode
EJECT + FNC + Reset
(Reference) Specification for Key Function when multiple
keys are pressed
5.3. Remote controller
The remote controller key speci
fi
cation is listed in Table 5.3.
(Note that the keys that are not listed in the table have con-
ventional functions.)
The mode of the remote controller shall be “AUDIO”.
Key
Function
FM
DVD video mode
AM
DVD audio mode
Tenkey0
Flicker Adjustment
Tenkey1
Tilt mechanism position adjustment
Tenkey2
DC Offset check
Tenkey3
V-IN (R-CAM) mirror mode switching
Tenkey5
Forced NAVI audio interruption
Tenkey6
Screen adjustment screen callout
Table 5.3 Remote Controller key
5.4. Video Control
In conjunction with the source, AV-OUT is also changed (Any
AV-OUT can be accepted when the source is other than the
followings).
Source: AV-IN
→
AV-OUT: AV-IN
Source: iPod
→
AV-OUT: iPod
Source: DVD
→
AV-OUT: DVD
Source: TV
→
AV-OUT: TV
Source: NAVI
→
AV-OUT: NAVI (DXN only)
5.5. Tuner
• When unable to access E2PROM, display Error (on the
Tuner screen).
• K3I forced switching
Forced to Narrow by pressing and hold Preset 4: xxx.
x1MHz
Forced to Middle by pressing and holding Preset 5: xxx.
x2MHz
Forced to Wide by pressing and holding Preset 6: xxx.
x3MHz
• Switch Span (K
↔
M) with [SRC] key + [Vol.DW] key + [Re-
set] key.
Span information is displayed on the Information screen.
• When RDS PS is “RDS_TEST” in the Tuner source, turn
OFF P-CON.
5.6. TV Tuner
• In the case of destination E, the default value of TV1 shall
be “Area 5 (Russia), 8ch (191.25MHz)” (when KTC-V500 is
connected).
• In the case of destination E, the default value of TV1 shall
be “Area 4 (Russia), 8ch (191.25MHz)” (when KTC-V300 is
connected).
∗
If started up as above, even if the Test mode is cleared
by ACC, Power OFF
→
ON, the setting values are main-
tained. (The default value is resumed by the Reset.)
TEST MODE