background image

English

   

|

   

3

Installation Procedure

1.  To prevent short circuits, remove the key from the 

ignition and disconnect the 

-

 terminal of the 

battery.

2.  Make the proper input and output wire 

connections for each unit.

3.  Connect the wire on the wiring harness.
4.  Take Connector B on the wiring harness and 

connect it to the speaker connector in your vehicle.

5.  Take Connector A on the wiring harness and 

connect it to the external power connector on your 
vehicle.

6.  Connect the wiring harness connector to the unit.
7.  Install the unit in your car.
8. Reconnect the 

-

 terminal of the battery.

9.  Press the reset button.

2

WARNING

•  If you connect the ignition wire (red) and the battery wire 

(yellow) to the car chassis (ground), you may cause a short 
circuit, that in turn may start a fire. Always connect those 
wires to the power source running through the fuse box.

¤

•  Mounting and wiring this product requires skills and 

experience. For safety’s sake, leave the mounting and wiring 
work to professionals.

•  Make sure to ground the unit to a negative 12V DC power 

supply.

•  Do not install the unit in a spot exposed to direct sunlight 

or excessive heat or humidity. Also avoid places with too 
much dust or the possibility of water splashing.

•  Do not use your own screws. Use only the screws provided. 

If you use the wrong screws, you could damage the unit.

•  If the power is not turned ON (“PROTECT” is displayed), 

the speaker wire may have a short-circuit or touched the 
chassis of the vehicle and the protection function may 
have been activated. Therefore, the speaker wire should be 
checked.

•  Make sure that all wire connections are securely made by 

inserting jacks until they lock completely.

•  If your vehicle’s ignition does not have an ACC position, or 

if the ignition wire is connected to a power source with 
constant voltage such as a battery wire, the power will not 
be linked with the ignition (i.e., it will not turn on and off 
along with the ignition). If you want to link the unit’s power 
with the ignition, connect the ignition wire to a power 
source that can be turned on and off with the ignition key.

•  Use a commercially available conversion connector if the 

connector does not fit in the vehicle connector.

•  Insulate unconnected wires with vinyl tape or other similar 

material. To prevent a short circuit, do not remove the caps 
on the ends of the unconnected wires or the terminals.

•  If the console has a lid, make sure to install the unit so that 

the faceplate will not hit the lid when closing and opening.

•  If the fuse blows, first make sure the wires aren’t touching 

to cause a short circuit, then replace the old fuse with one 
with the same rating.

•  Connect the speaker wires correctly to the terminals to 

which they correspond. The unit may be damaged or fail to 
work if you share the 

-

 wires or ground them to any metal 

part in the car. 

•  After the unit is installed, check whether the brake lamps, 

blinkers, wipers, etc. on the car are working properly.

•  Mount the unit so that the mounting angle is 30° or less.
•  This unit has the cooling fan (page 5) to decrease the 

internal temperature. Do not mount the unit in a place 
where the cooling fan of the unit are blocked. Blocking 
these openings will inhibit the cooling of the internal 
temperature and result in malfunction.

•  Do not press hard on the panel surface when installing the 

unit to the vehicle. Otherwise scars, damage, or failure may 
result.

B54-4621-00̲00̲en.indd   3

B54-4621-00̲00̲en.indd   3

07.12.18   3:18:39 PM

07.12.18   3:18:39 PM

Содержание DDX5022













Отзывы: