REV F: 30/12/05
KENTMASTER MFG. CO., INC.
1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016
UNITED STATES OF AMERICA
TELEPHONE: (626) 359-8888 FAX: (626) 303-5151
4 OF 43
CLEANING AND STERILIZING SAW
AT END OF EACH SHIFT:
1.
REMOVE SAW BLADE.
2.
CLEAN AND WASH DOWN BOTH INSIDE AND OUTSIDE OF ENTIRE MACHINE THOROUGHLY WITH HOT WATER
AND CLEANING AGENT. AVOID USING HARSH CAUSTIC CLEANERS ON MACHINE.
3.
WASH OFF ALL BONE DUST AND MEAT PARTICLES FROM INSIDE OF FRAMES, AROUND WHEELS AND GUIDES.
4.
SPRAY BOTH INSIDE AND OUTSIDE OF MACHINE WITH A LIGHT COAT OF MINERAL OIL.
WATER CONNECTION
A BULKHEAD FITTING, FIGURE 1, ITEM 10, IS PROVIDED AT THE BASE OF DRIVE SIDE FRAME, ITEM 11, FOR
CONNECTION TO COLD WATER. ADJUST CONNECTOR AND NOZZLE, ITEMS 12 AND 13, TO CLEAN BONE DUST
FROM DRIVE WHEEL AND MEAT PARTICLES TRAPPED BETWEEN TEETH OF SAW BLADE. FITTING AND HOSE,
ITEMS 14 AND 15, AT BASE OF DRIVE SIDE FRAME, ARE PROVIDED FOR DRAINAGE OF WASTE WATER.
TORQUE WRENCH CALIBRATION
TORQUE WRENCH, ITEM 5, IS CALIBRATED AND PRESET TO 55 INCH/LBS AT FACTORY. PERIODICALLY CHECK
CALIBRATION BY USE OF ANOTHER TORQUE WRENCH WITH A DIAL TO MAKE ADJUSTMENT AND RESET TORQUE
WRENCH TO 55 INCH/LBS. REMOVE TORQUE WRENCH COVER TO
CLEAN AND LUBRICATE PERIODICALLY.
TESTING AND SETTING OF TORQUE WRENCH:
TOOLS REQUIRED:
HEX WRENCH -- 3/16"
HEX BAR -- 1/2", ABOUT 3"-6" LONG
HEX SOCKET -- 1/2" WITH DRIVE END TO MATCH COMMERCIAL WRENCH SELECTED
TORQUE WRENCH, COMMERCIAL DIAL TYPE PREFERABLE
SCREWDRIVER -- 3/8"-7/16" FLAT BLADE
STEP 1 -- TESTING KENTMASTER TORQUE WRENCH
A.
ATTACH COMMERCIAL TORQUE WRENCH TO KENTMASTER TORQUE WRENCH USING 1/2" HEX BAR AND
1/2" HEX SOCKET.
B.
HOLD ASSEMBLY FIRMLY AND ROTATE KENTMASTER TORQUE WRENCH CLOCKWISE SLOWLY UNTIL
WRENCH
"SLIPS".
C.
INDICATOR NEEDLE ON COMMERCIAL TORQUE WRENCH SHOULD READ 55 IN/LBS ±3 IN/LBS (5%).
IF OVER OR UNDER VALUE, PROCEED TO STEP 2 -- RESETTING KENTMASTER TORQUE WRENCH.
STEP 2 -- RESETTING KENTMASTER TORQUE WRENCH
A.
USING 3/16" HEX WRENCH, REMOVE FOUR (4) SCREWS HOLDING THE WRENCH HANDLE IN PLACE.
REMOVE HANDLE AND GASKET. SET ALL PARTS ASIDE FOR REUSE.
B.
HOLD WRENCH BODY SECURE BY EITHER CLAMPING SMALL DRIVE END IN VISE OR BY CLAMPING THE
1/2" HEX BAR IN VISE AND ATTACHING WRENCH TO BAR.
C.
USE FLAT BLADE SCREWDRIVER TO ADJUST THE FOUR (4) SET SCREWS UNDER WRENCH HANDLE.
USE A STAGGERED PATTERN WHILE ADJUSTING, SUCH AS UPPER, LOWER, LEFT THEN RIGHT.
•
TO REDUCE TORQUE VALUE - BACK OFF SET SCREWS COUNTER-CLOCKWISE ABOUT 1/8 TURN EACH.
•
TO INCREASE TORQUE VALUE - TURN IN SET SCREWS CLOCKWISE ABOUT 1/8 TURN EACH.
D.
REASSEMBLE TORQUE WRENCH WITH HANDLE AND GASKET. RETEST PER STEP 1. CONTINUE TESTING
AND SETTING UNTIL WRENCH OPERATES AT PROPER TORQUE VALUE.
NOTE: Do not clamp body of Torque Wrench in vise as
severe damage to Torque Wrench could occur.
