KENT C-4 Скачать руководство пользователя

Страница: 9 / 53

Excessive

Vacuum Motor

noise.

1. Worn

Vacuum Motor

bearings

and / or fan blades.

1. Replace

Vacuum Motor. (18007)

(See Repair Manual: Removing
Vacuum and Brush Assembly, and
Replacing Vacuum Motor.)

Burnt motor smell from clean air
exhaust.

1. Worn

Vacuum Motor

brushes.

NOTE:

Excessive sparking may also

occur.

1. Replace

Vacuum Motor (18007).

(See Repair Manual: Removing
Vacuum and Brush Assembly, and
Replacing Vacuum Motor.)

All switches are ON, ONLY

Vacuum

Motor

does not run.

1. Defective

Vacuum Motor.

TEST:

Test

Vacuum Motor

(18007) using

Vacuum / Brush Motor

Test Cable (7202)

. If motor runs,

there is a problem with the electrical
system.

NOTE:

If motor does not

work, replace

Vacuum Motor

(18007). (See Repair Manual:
Removing Vacuum and Brush
Assembly, and Replacing Vacuum
Motor.)

2. Defective

Switch

2. Replace

Switch (10108)

Terminals

not connected or

defective.

3. Re-connect or replace

Terminals

Dirty liquid is being discharged
through the

Vacuum Motor Exhaust

Tube (C4:10101 / C4-A: 10608).

1. The cleaning solution was not
poured from the

Bucket

into the

Solution Tank

1. Pour the cleaning solution from the

Bucket

into the

Solution Tank

NOTE:

The solution is being sucked

into the

Vacuum Motor

and then

blowing out the

Exhaust Tube.

2. Foam is building up in the

Bucket

. 2. Empty

Bucket

without refilling the

Solution Tank

. If available, add Anti

Foam to the emptied

Bucket

CLEAN UP Step 1:

Sit the

Bucket

aside. Move the machine to concrete
surface, such as the garage. Leave
the

Lid

up. Run the

Vacuum Motor

only for 1 minute to blow out any
remaining liquid.

3. Too much liquid was added to the

Solution Tank

3. Empty

Bucket

without refilling the

Solution Tank

. Do not exceed top Fill

Line of

Bucket

. Add less water to the

Solution Tank

during next cleaning

cycle.

Step 2:

Clean the discharged dirty

liquid from carpet

immediately

Spot

Remover

7 in 1

may be needed.

ALSO:

Using the

Hand Tool

may lift

spot better.

VACUUM SYSTEM CONTINUED

Содержание C-4






















































Результаты поиска

Содержание C-4

Отзывы:

Похожие инструкции для C-4

Бренды по названию

Популярные бренды

KENT C-4, Руководство пользователя

Результаты поиска

Содержание C-4

Отзывы:

Похожие инструкции для C-4

Бренды по названию

Популярные бренды