K
G
H
J
I
N
A
L
M
D
P
O
C
B
E
F
VB Parts Desc.
ASSEMBLY SUPPLY LIST
KEY
PART DESCRIPTION
MODEL NUMBER
4804 4806 6006 6012E 6012ED 6012S
A
Kennedy Tool Chest
0
1
1
2
2
2
B
Chrome Plated Push Handle
1
1
1
1
1
1
C
1/4” x 3/4” Hex Head Bolts
4
4
4
4
4
4
D
Double Head Nut
2
2
2
2
2
2
E
8 x 2” Swivel Casters
2
2
2
2
2
2
F
Floor Lock
1
1
1
1
1
1
G, I
3/8 x 3/4” Hex Head Bolts
20
20
20
20
20
20
H, J 3/8” Hex Lock Nuts
20
20
20
20
20
20
K
8 x 2” Rigid Casters
2
2
2
2
2
2
L
“L” Shaped Aluminum Door Handles
2
2
4
4
8
2
M
1/2” Hex Head Screws
4
4
8
8
16
4
N
White Plastic Feet
0
4
4
8
8
8
O
1/4” x 3/4” Round Head Screw
0
2
2
4
4
4
P
Washer
0
2
2
4
4
4
Versa-Bench
®
Assembly Instructions
Note: For towing package assembly, refer to assembly instructions on back page.
1. Remove tool chest(s) (A) from Versa-Bench, set aside.
Does not apply to model 4804.
2. Fasten chrome push handle (B) to end of bench as shown using (4) 1/4” x 3/4” hex head bolts (C) and
(2) double head nut (D).
Note:
4804, 4806 push handle assembles to left ends into extruded holes with 1/4”
thread cutting bolt.
3. Lift bench with a fork lift or lay on its back on shipping carton to install swivel casters (E) and floor lock (F).
Remove bolts from wood shipping blocks from inside bottom of the Versa-Bench.
4. Fasten swivel casters (E), as shown, at the same end as the push handle (B) with (8) 3/8” x 3/4” hex bolts (G)
and (8) 3/8” lock nuts (H). Bolt head should be inside bench, lock nut under bench.
5. Fasten the floor lock (F), as shown between the swivel casters (E) with (4) 3/8” x 3/4” hex bolts (I) and
(4) 3/8” lock nuts (J). Bolt head should be inside bench, lock nut under bench.
6. Fasten rigid casters (K) to opposite end of bench with (8) 3/8” x 3/4” hex bolts and (8) 3/8” lock nuts.
Carefully set bench upright.
7. Fasten each door handle (L) to each door with (2) 1/2” hex head screws (M). Center the handle on the two
holes provided in the door. Fasten the screws thru the holes into the base of the handle.
8.
Tool chest installation:
Does not apply to model 4804. Remove tool chest(s) (A) from carton(s). Supplies are
in an envelope in a drawer.
9. Snap (4) plastic feet (grommets) (N) in place, up thru the four holes in the bottom of each tool chest.
10. Slide tool chest into position inside the bench and fasten with (2) 1/4” x 3/4” round head screws (O) with
washers (P) thru the slots in bench compartment wall into the threaded holes in the tool chest back.
