When using electrical appliances, basic
precautions should always be followed to reduce
the risk of fire, electric shock and injury to
persons, including the following:
• Always use this fan only as described in this
manual. Other uses not recommended may
cause fire, electric shock or injury to persons.
• Always supervise as necessary when any
appliance is used by or near children.
• Always avoid contact with moving fan parts.
• Always turn the fan to the OFF position and
unplug the fan from the outlet when not in use
and before cleaning.
• Always place the fan on a dry level surface.
• Always check that the filters are clear and
not blocked. Keep all openings clear of any
blockages.
• Do not use this product outdoors.
• Do not pull by the cord. To disconnect the fan,
first turn control to the OFF position, grip the
plug and pull it from the wall outlet.
• Do not operate the fan in the presence of
explosive and/or flammable fumes.
• Do not place the fan or any parts near an open
flame, cooking or other heating appliance.
• Do not hang or mount fan on a wall or ceiling.
• Do not operate the fan with a damaged cord or
plug or if the product malfunctions, is dropped
or damaged in any manner.
• Do not operate if the fan housing is removed
or damaged.
• Do not operate the fan without checking that
the protective front and rear grill are
in position.
• To protect against electric shock, do not
immerse unit, plug or cord in water or spray
with liquids.
• Do not connect this fan to any power source
other than properly grounded ones. DO NOT
attempt to defeat this safety feature. This fan
requires a grounded power source.
• The use of attachments is not recommended
and may be hazardous.
• A loose fit between the AC outlet (receptacle)
and plug may cause overheating and a
distortion of the plug. Contact a qualified
electrician to replace loose or worn outlet.
• If the power cord is damaged, it must be
replaced by the qualified electrician or
professional technician in order to avoid
a hazard.
This product has been specifically designed to help you work
SAFELY
and
EFFICIENTLY
. Your care and
good judgement are the best protection against injury, but always ensure that the appropriate safety
equipment is worn. All possible hazards cannot be covered here, but the most important ones have
been highlighted.
SAFETY INSTRUCTIONS
You have purchased a quality product that is designed for high performance and long service
life. If correct use, safety and maintenance procedures are observed this machine will last for many years.
ELECTRICAL INFORMATION
ASSEMBLY
PARTS BREAKDOWN
In the United Kingdom, the
ELECTRICITY AT WORK ACT 1989
requires all portable electrical
appliances, if used on business premises, to be tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year. The
HEALTH & SAFETY AT WORK ACT 1974
makes
owners of electrical appliances responsible for the safe condition of the appliance and the safety of its
operator. If in any doubt about electrical safety, contact a qualified electrician.
ELECTRICAL SAFETY
• An RCCB (Residual Current Circuit Breaker) should be fitted in the mains electricity distribution
board. If the power supply is not protected by an RCCB, it is highly recommended that an RCD
(Residual Current Device) is used with all portable electrical products.
• Do not use any adaptor plugs.
• Do not carry or yank the fan by the cord.
• Never expose to wet conditions as this will increase the risk of electric shock.
SPECIFICATIONS
Order Code:
CTL-828-9140H
Voltage:
AC220-240V
Frequency:
50Hz
Power:
45W
1.
Set the base on a level dry surface and cover the base cover,then install the outer pipe and match the 4 holes over
the 4 screw holes on the base and use the 4 screws to tighten.
2.
Place the base on through the column with the tabs/slots pointing downward and unscrew the height adjustable
control collar from the outer pipe.
3.
Slide the stand base end cap down over the inner and outer pipe until it is in place over the screws.
4.
Replace the height adjustable control collar and at the same time raise the inner pipe then tighten the collar.
5.
Place the fan motor into the top of the inner pipe, tighten the set screw.
6.
Unscrew the plastic grill nut on the front of the motor by turning anti-clockwise.
7.
Mount the rear grill to the motor front cover by matching the 2 holes on the guard to the 2 round positioning knobs on
the motor front cover. Push in firmly until the 2 knobs protrude through the 2 holes.
8.
Replace and tighten the grill nut by turning the nut clockwise to hold the rear grill in place.
9.
Put the fan blade onto the motor shaft by matching the shafts slots with the blades slot, tighten the blade with the
blade cap by turning it anti-clockwise.
10.
Test fan by rotating with your hands, make sure there isn’t any contact with the cap. The fan blade should rotate freely.
11.
Use 3 screws to install the Grill ring in the middle of front grill.
12.
Mount Front Grill onto Rear Grill by hanging the top hook clip of front grill over the top of the Rear Grill. Close the nut all
around the grill and then use the safety screw to tighten the grill.
CAUTION: To avoid the risk of injury, always make sure that the front and rear grill are
locked together before operating.
OPERATION
• Place your fan on a level and dry surface.
• Do not operate the fan without the guards properly in place.
• Ensure voltage used corresponds with the voltage indicated.
• Turn the speed control to selected speeds: 0(off) and speeds 1 low, 2 medium and 3 high.
• To start or stop fan head oscillating, press or pull the oscillating knob on the top of the motor housing.
• To change the air flow angle, move the head forward or backwards.
• Never touch the moving blades with hand or object.
• Always unplug the fan when moving or not in use and store in a cool, dry place.
2
3
Index
No.
Description
1.
Front Grill
2.
Fan Blade
3.
Rear Grill
4.
Motor
5.
Control Panel
6.
Set Screw
7.
Height Adjustable
Control Collar
8.
Outer Pipe
Index
No.
Description
9.
Screw
10.
Base
11.
Base Cover
12.
Stand Base End Cap
13.
Inner Pipe
14.
Plastic Grill Nut
15.
Blade Cap
1
2
3
4
5
6
7
8
9
9
10
11
12
13
14
15
9
MAINTENANCE
• Unplug or disconnect the power cord from the mains before servicing.
• Lift the clips on ring of the guards and remove the front guard. Lock the guard securely before use.
• First use a soft cloth with light soap to clean off dirt/dust, then wipe and polish with dry cloth.
• Never use polish or any corrosive liquid that will damage the paint, metal or plastic.
• Store in a cool, dry place. You can leave the fan assembled and covered to protect it from dust.
