Kenmore W10213167A, Инструкция по использованию и уходу

Страница: 26 / 84

26
Base Grille Water Filtration System
Model P1KB1/P1RFKB1 Capacity 100 Gallons (379 Liters)
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 100 gallons (379 liters).
■ It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
■ Model P1KB1: The filter monitor system measures the amount of
water that passes through the filter and alerts you to replace the
filter.
Style 1 - When the filter indicator reads 10%, order a new filter.
When the indicator reads 0%, it is recommended that you
replace the filter.
Style 2 - When the filter indicator changes from green to yellow,
order a new filter. When the indicator changes from yellow to red,
it is recommended that you replace the filter.
Style 3 - When the water filter status display changes from
“GOOD” to “ORDER,” order a new filter. When the filter indicator
reads “REPLACE,” it is recommended that you replace the filter.
Use replacement cartridge P1RFKB1, part #9030.
2008 suggested retail price of $59.99 U.S.A./$71.99 Canada.
Prices are subject to change without notice.
■
These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
■ The product is for cold water use only.
■ Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
■ Refer to the “Warranty” section for the Manufacturer’s name,
address and telephone number.
■
Refer to the “Warranty” section for the Manufacturer’s limited
warranty.
Application Guidelines/Water Supply Parameters
System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of
Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of
Lead, Mercury, Atrazine, Benzene, Toxaphene, O-Dichlorobenzene, Cysts, Turbidity, Asbestos, Lindane,
Tetrachloroethylene, Endrin, Alachlor, Styrene, Chlorobenzene, Ethylbenzene, TTHM, MTBE and VOC.
Substance Reduction
Aesthetic Effects NSF Reduction
Requirements Average
Influent Influent Challenge
Concentration Maximum
Effluent Minimum %
Reduction Average %
Reduction
Chlorine Taste/Odor
Particulate Class I
*
50% reduction
85% reduction 2.10 mg/L
21000000#/mL 2.0 mg/L ± 10%
At least 10,000 particles/mL 0.05 mg/L
140000 #/mL
**
97.6
99 97.6
99.5
Contaminant
Reduction NSF Reduction
Requirements Average
Influent Influent Challenge
Concentration Maximum
Effluent Minimum %
Reduction Average %
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.5 0.010 mg/L
0.010 mg/L 150 ug/L
160 ug/L 0.15 mg/L ± 10%
0.15 mg/L ± 10% 1.0 ug/L
2.0 ug/L 99.3
99.4 99.3
99.3
Mercury: @ pH 6.5
Mercury: @ pH 8.5 0.002 mg/L
0.002 mg/L 5.8 ug/L
6.1 ug/L 0.006 mg/L ± 10%
0.006 mg/L ± 10% 0.2 ug/L
0.4 ug/L 96.6
93.4 96.6
95.3
Benzene 0.005 mg/L 15 ug/L 0.015 mg/L ± 10% 0.5 ug/L 96.7 96.7
O-Dichlorobenzene 0.6 mg/L 1900 ug/L 1.8 mg/L ± 10% 0.7 ug/L 99.9 99.9
Toxaphene 0.003 mg/L 14 ug/L 0.015 mg/L ± 10% 1.0 ug/L 91.5 92.8
Atrazine 0.003 mg/L 9.0 ug/L 0.009 mg/L ± 10% 0.5 ug/L 94.5 94.5
Asbestos 99% 130 MFL 10
7
to 10
8
fibers/L
††
0.17 MFL 99 99
Live Cysts
‡
Turbidity
>99.95%
0.5 NTU 96,000/L
12 NTU 50,000/L min.
11 ± 1 NTU 1/L
‡
0.4 NTU
99.99
96.7 99.99
98.5
Alachlor 0.002 mg/L 41 ug/L 0.04 mg/L ± 10% 1.0 ug/L 97.6 97.6
Endrin 0.002 mg/L 5.9 ug/L 0.006 mg/L ± 10% 0.2 ug/L 96.5 96.6
Ethylbenzene 0.7 mg/L 2100 ug/L 2.1 mg/L ± 10% 0.5 ug/L 99.9 99.9
Lindane 0.0002 mg/L 1.9 ug/L 0.002 mg/L ± 10% 0.02 ug/L 99 99
Chlorobenzene 0.1 mg/L 2100 ug/L 2.0 mg/L ± 10% 1.1 ug/L 99.9 99.9
Tetrachloroethylene 0.005 mg/L 14 ug/L 0.015 mg/L ± 10% 0.5 ug/L 96 96.4
Styrene 0.1 mg/L 2200 ug/L 2.0 mg/L ± 10% ND (0.5) 99.9 99.9
TTHM 0.080 mg/L 480 ug/L 0.45 ± 20% 3.9 ug/L 99.2 99.8
MTBE 0.005 mg/L 15 ug/L 0.015 ± 20% 1.3 ug/L 91.3 96.2
VOC 0.05 mg/L 300 ug/L 300 ± 30 ug/L ND (0.5) 99.8 99.8
Water Supply
Water Pressure
Water Temperature
Service Flow Rate City or Well
30 - 120 psi (207 - 827 kPa)
33° - 100°F (0.6° - 37.8°C)
0.5 gpm (1.9 L/min) @ 60 psi
*
**
††
‡
Class I particle size: >0.5 to <1 um
Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
Fibers greater than 10 um in length
Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.