Kenmore Over The Range Microwave Oven, Руководство по установке

Страница: 16 / 48

INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
been properly routed and secured,
and that the wires are not pinched.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Back of
Microwave
Installation Instructions
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
B1.
You need to cut an opening in the rear wall for
outside exhaust.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
B2.
OUTSIDE BACK EXHAUST
(Horizontal Duct)
B
Blower Plate
REMOVE BLOWER PLATE
B2. Remove Blower Plate
3/8" TO EDGE



 













NOTE: IT IS VE
RY IMPOR
TANT TO
READ AND
FOLLOW TH
E DIRECTIONS
IN THE IN
STALLATIO
N INSTRUCTIO
NS
BEFORE PR
OCEEDING
WITH THIS
REAR WALL
TEMPLATE
.
This Rear Wall
Template serv
es to position
the bottom
mounting plate a
nd to locate the
horizontal exhaust
outlet.
1. Use a level
to check that th
e template is posi
tioned
accurat
ely. 2. Locate and
mark at least one
stud on the lef
t or
right side
of the centerline. 
It is important
to use at leas
t one wood
screw mounted
firmly in a stud
to support the
weight
of the microw
ave. Mark two
additional, evenly
spaced
locations for the
supplied toggle
bolts.
3. Drill holes
in the marked
locations. Wh
ere there is
a stud, drill a
3/16" hole for wood
screws. For hol
es
that do not li
ne up with a stu
d, drill 5/8" hole
s for
toggle bolts.

DO NOT INSTALL
THE MOUNT
ING PLATE
AT THIS TIME.
4. Remove the
template from
the rear wall.
5. Review
the Installation
Instruction boo
k for your
installation sit
uation.
Locate and
mark holes to
align with ho
les in the
mounting p
late. IMPORTANT:
LOCATE
AT LEAST ON
E STUD ON EITH
ER SIDE OF
THE CENTER
LINE. MARK TH
E LOCATION FOR
2 ADDITIONAL
, EVENLY
SPACED TOGG
LE BOLTS IN
THE MOU
NTING PLA
TE
AREA.
Locate and
mark holes to
align with h
oles in the
mounting plate
. IMPORTA
NT:
LOCATE
AT LEAST ON
E STUD ON EIT
HER SIDE
OF
THE CENTER
LINE. MARK TH
E LOCAT
ION FOR
2 ADDITIONAL
, EVENLY
SPACED TOGG
LE BOLTS
IN THE MOU
NTING PLA
TE
AREA.
Trim the rear wa
ll template a
long the d
otted line.
Trim the rear wall
template along
the dotted
line.













12"
4"
Darle vuelta a la
hoja para consul
tar la
versión en Españ
ol.
Make sure the motor wiring has
3/8" TO EDGE
NOTE: IT IS VERY IMPOR
TANT TO
READ AND FOLLOW THE
DIRECTIONS
IN THE INSTALLATION IN
STRUCTIONS
BEFORE PROCEEDING WITH
THIS
REAR WALL TEMPLATE.
This Rear Wall Template serv
es to position the bottom
mounting plate and to locate th
e horizontal exhaust
outlet.
1. Use a level to check that the
template is positioned
accurately.
2. Locate and mark at least o ne stud on the left or
right side of the centerline.
It is important to use at least on
e wood
screw mounted firmly in a stud
to support the weight
of the microwave. Mark two a
dditional, evenly spaced
locations for the supplied tog gle bolts.
3. Drill holes in the marked lo cations. Where there is
a stud, drill a 3/16" hole for
wood screws. For holes
that do not line up with a s
tud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOU
NTING PLATE
AT THIS TIME.
4. Remove the template from
the rear wall.
5. Review the Installation Inst
ruction book for your
installation situation.
Locate and mark holes to a
lign with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD
ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FO
R 2 ADDITIONAL, EVENL
Y
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to a
lign with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE O
F
THE CENTERLINE.
MARK THE LOCATION FO
R 2 ADDITIONAL, EVENL
Y
SPACED TOGGLE BOLTS I
N THE MOUNTING PLATE
AREA.
Trim the rear wall template along
the dotted line.
Trim the rear wall template
along the dotted line.
12"
4"
Darle vuelta a la hoja para co nsultar la
versión en Español.
EN-16