Kenmore 795.75312.900 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 41

background image

- 28 -

8-1-11 TEST MODE

1. Test mode allows checking the PCB and the function of the product as well as determining the Defective part in case of an
error.
2. The test button is on the main PCB of the refrigerator (Test S/W).
3 While in the test mode, the ADJUST button will not operate.
4. After exiting the test mode, be sure to reset by unplugging and plugging in the appliance,
5. If an error, such as a sensor failure is detected while in the test mode, the test mode is cleared and the error code is
displayed.
6. While an error code is displayed, the test mode will not be activated.

MODE Key Control Operation Remarks

   1) Continuous operation of the
Push the test    COMP, Freezer FAN
button once    and Cooling FAN. *The maximum
TEST 1     2) DEFROSTING HEATER OFF time for TEST 1
   3) ALL DISPLAY ON is 5 min.
   4) LAMP RELAY ON/OFF
   OPERATED BY DOOR SWITCH

   1) COMP OFF Ref. Temp. Display
Push the test    2) Freezer FAN and Cooling
button once while FAN OFF

in TEST MODE 1 3) Defrosting Heater ON
TEST    4) 1, 3, 5 LED ON

      Operate max 1 Hr

Push the test button Reset to the default settings
Once while in TEST (Compressor will delay 7
RESET MODE 2 minutes for Power ON)

:ON :OFF

R1

R3

R5

«
...
26
27
28
29
30
...
»

Содержание 795.75312.900










































Отзывы:

Нет отзывов

Похожие инструкции для 795.75312.900

Echelon CO2075FF

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 20

Echelon 2115RS00

Бренд: U-Line Страницы: 20

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 58

Combo CO2175DWR

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 35

Бренд: U-Line Страницы: 2

WINE CAPTAIN 2275DWRCOL

Бренд: U-Line Страницы: 17

Бренд: U-Line Страницы: 32

Бренд: Concept2 Страницы: 71

Бренд: DAEWOO ELECTRONICS Страницы: 5

Бренд: KBS Gastrotechnik Страницы: 54

Combo U-CO29FB-00A

Бренд: U-Line Страницы: 16

Бренд: Cylinda Страницы: 86

Бренд: Smeg Страницы: 14

Бренд: SPARES ZONE Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды