Kenmore 795.71302.010 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 42

background image

7-1 OPERATION PRINCIPLE

7-1-1 Operation Principle of Icemaker

1. Turning the Icemaker stop switch off (O) stops the icemaking function.
2. Setting the Icemaker switch to OFF and then turning it back on will reset the icemaker control.

7. OPERATION PRINCIPLE AND REPAIR METHOD OF ICEMAKER

- 23 -

Initial Control

Icemaking

Control

Water supply control

• Waits until water in the TRAY is frozen after Icemaker

Starts operation.

• Runs MOTOR to drop ice from the tray into the ICE BIN.

• Performs

Icemaking Mode

after supplying water by operating

the SOLENOID in ICE VALVE.

• To operate LINE and SERVICE, press and hold the

Fill Key

for 3 seconds. The icemaking will run through 3 stages:

Harvest Fill Icemaking

.

Power Input

• Adjusts Ejector to

Start Position

with power on.

Ice Ejection

Control

Feeler Arm

Power Switch

Icemaker

TEST Control

Test Switch

«
...
21
22
23
24
25
...
»

Содержание 795.71302.010











































Отзывы:

Нет отзывов

Похожие инструкции для 795.71302.010

Бренд: Gaggenau Страницы: 81

RC472700 - annexe 2

Бренд: Gaggenau Страницы: 60

Бренд: Gaggenau Страницы: 77

Бренд: Gaggenau Страницы: 33

Бренд: Gaggenau Страницы: 82

Бренд: Gaggenau Страницы: 36

Бренд: Gaggenau Страницы: 87

Бренд: Gaggenau Страницы: 53

Бренд: Samsung Страницы: 466

Бренд: inventum Страницы: 64

Бренд: Grundig Страницы: 104

Бренд: Maytag Страницы: 36

Бренд: True Страницы: 2

Бренд: Smeg Страницы: 12

Бренд: NEFF Страницы: 30

Millennium DAR452BL

Бренд: Danby Страницы: 30

Бренд: ZANKER Страницы: 18

Бренд: Maytag Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды