background image

8-1-10 TEST Mode

1. The Test mode allows checking the PCB and the function of the product as well as finding out the defective part in case of

an error.

2. The test mode is operated by pressing two buttons at Display panel.

3. While in the test mode, the function control button is not recognized, but the recognition tone (beep~) sounds.

4. After exiting the test mode, be sure to reset by unplugging and then plugging in the appliance.

5. If an error, such as a sensor failure, is detected in the test mode, the test mode is cleared and the error code is

displayed.

6. While an error code is displayed, the test mode will not be activated.

NOTE 

LED CHECK MODE: When the ADJUST REFRIGERATOR TEMP KEY & ADJUST FREEZER TEMP Keys are pressed at the

same time and hold for 1 second or longer, every LED on the display turns on at the same time. when the button are

relesed, the previous mode is restored. 

* Freezer Fan RPM Variable Check:

In case the freezer fan is in operation when the COLD KEY in Refrigerator and Freezer Temp. Control are pressed for
more than one second at the same time freezer fan RPM changes. (for example if high speed, to normal speed or if
normal speed, to high speed for 30 seconds) 
After 30 seconds, it turns to its original RPM.

* Demonstration MODE:

1. When the ULTRA ICE key and ADJUST key of refrigerator temperature control are pressed for

more than 3 seconds at the same time, temperature’s it converts to demonstration mode.

2. In this status, each LED is rotated with 1 second interval.
3. In this status, all Loads are off (Compressor / Fan / Damper / Heater)

(Even is Demonstration Mode, the refrigerator Lamp automatic off function warks normally and can be demonstrated)

4. It reset if you do again as clause.

- 24 -

MODE

MANIPULATION

CONTENTS

REMARKS

TEST1

TEST2

Reset

Push ULTRA ICE &

ADJUST FREEZER

TEMP Keys at the 

same time over 3

seconds.

Push ULTRA ICE &

ADJUST FREEZER

TEMP Keys at the

same time over 3 seconds

in TEST MODE 1

Push ULTRA ICE &

ADJUST FREEZER

TEMP Keys at the

time over 3 seconds. in

TEST MODE 2

1. Continuous operation of the

COMPRESSOR

2. Continuous operation of the freezer fan

3. STEPPING DAMPER OPEN

4. Defrosting Heater OFF

5. Every DISPLAY LED ON

1. COMP OFF

2. Freezer FAN OFF

3. STEPPING DAMPER CLOSE

4. Defrosting heater ON

5. DISPLAY LED 1, 3, 5, 7 ON

Reset to the previously setting before 

TEST MODE

Reset if the

temperature of the 

Defrosting sensor is 

46

°

F (8

°

C) or more.

The compressor will

Start after a 7-minute

delay.

Содержание 795.65002.402





















































Отзывы: