background image

13

Location Requirements                                              

Carbon Monoxide Poisoning Hazard

WARNING

Do not install in a mobile home.  

Doing so can result in carbon monoxide poisoning and death.  

The FVIR System is designed to reduce the risk of flammable 
vapor-related fires. The patented system protects your family by 
trapping the burning vapors within the water heater combustion 
chamber through the special flame-arrestor. The burning vapors 
literally “burn themselves out” without escaping back into the 
room. In the event of a flammable vapor incident, the FVIR 
System disables the water heater by shutting off the gas supply 
to the water heater’s burner and pilot, preventing re-ignition 
of any remaining flammable vapors in the area. This will not 
prevent a possible fire/explosion if the igniter is depressed 
and flammable vapors have accumulated in the combustion 
chamber with the pilot light off. If you suspect a flammable 
vapor incident has occurred, do not use this appliance. Do not 
attempt to light this appliance, or depress the igniter button 
if you suspect flammable vapors have accumulated inside or 
outside the appliance. Immediately call a qualified technician to 
inspect the appliance. Water heaters subjected to a flammable 
vapors incident will show a discoloration on the flame-arrestor 
and require replacement of the entire water heater.

FIRE AND EXPLOSION HAZARD

Can result in serious injury or death

        

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 
appliance. Storage of or use of gasoline or other 
flammable vapors or liquids in the vicinity of this or any 
other appliance can result in serious injury or death.

Flammable Vapors

FLAMMABLES

Read and follow water heater warnings and instructions.

WARNING

Do not use or store flammable products such as gasoline, 
solvents, or adhesives in the same room or area near the 
water heater. If such flammables must be used, all gas burning 
appliances in the vicinity must be shut off and their pilot lights 
extinguished. Open the doors and windows for ventilation while 
flammable substances are in use. 

If flammable liquids or vapors have spilled or leaked in the 

area of the water heater, leave the area immediately and call 
the fire department from a neighbor’s home. Do not attempt to 
clean the spill until all ignition sources have been extinguished.

Fire or Explosion Hazard

WARNING

•  Read instruction manual before installing, using or 
  servicing water heater.

•  Improper use may result in fire or explosion.

•  Maintain required clearances to combustibles.

Keep combustibles such as boxes, magazines, clothes, etc. 
away from the water heater area. 

Site Location                                                          

• 

Select a location near the center of the water piping system. 

The water heater must be installed indoors and in a vertical 

position on a level surface. DO NOT install in bathrooms, 

bedrooms, or any occupied room normally kept closed.

• 

Locate the water heater as close to the chimney or gas 

vent  as  practical.  Consider  the  vent  system  piping  and 

combustion air supply requirements when selecting the 

water heater location. The venting system must be able 

to run from the water heater to termination with minimal 

length and elbows. 

• 

Locate the water heater near the existing gas piping. If 

installing a new gas line, locate the water heater to minimize 

the pipe length and elbows. 

• 

The water heater should be located in an area not subject 

to freezing temperatures. Water heaters located in 

unconditioned spaces (i.e., attics, basements, etc.) may 

require insulation of the water piping and drain piping 

to protect against freezing. The drain and controls must 

be easily accessible for operation and service. Maintain 

proper clearances as specified on the rating plate.

• 

Do not locate the water heater near an air-moving device. 

The operation of air-moving devices such as exhaust fans, 

ventilation systems, clothes dryers, fireplaces, etc., can 

affect the proper operation of the water heater. Special 

attention must be given to conditions these devices may 

create. Flow reversal of flue gases may cause an increase 

of carbon monoxide inside of the dwelling (Figure 8).

• 

If the water heater is located in an area that is subjected to 

lint and dirt, it may be necessary to periodically clean the 

base-ring filter and flame-arrestor (see External Inspection 

& Cleaning of the Flame-arrestor). 

• 

This water heater is 

not

 for use in manufactured (mobile) 

homes or outdoor installation.  

NOTE:  This water heater must be installed according to all local 
and state codes or, in the absence of local and state codes, the 
“National Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition.

REVERSE FLOW
OF GASES 

 

EXHAUST FAN

FIGURE 8

Содержание 153.331140













































Отзывы: