background image

 

 

6

 

LP Tank Exchange 

•Many retailers that sell grills offer you the option of replacing 

your empty LP tank through an exchange service. Use only 
those reputable exchange companies that inspect, precision 
fill, test and certify their cylinders. Exchange your tank only 
for
 an OPD safety feature-equipped tank as described in 
the
 "LP Tank" section of this manual. 

 
Always keep new and exchanged LP tanks in upright position 

during use, transit or storage. 

 
Leak test new and exchanged LP tanks BEFORE 

connecting to grill.

 

 
LP Tank Leak Test 

For your safety 
 
Leak test must be repeated each time LP tank is exchanged 

or refilled. 

Do not smoke during leak test. 
Do not use an open flame to check for gas leaks. 
Grill must be leak tested outdoors in a well-ventilated area, 

away from ignition sources such as gas fired or electrical 
appliances. During leak test, keep grill away from open 
flames or sparks. 

•Use a clean paintbrush and a 50/50 mild soap and water 

solution. Brush soapy solution onto areas indicated by arrows 
in figure below. Leaks are indicated by growing bubbles. 
   

 

 

 

 

Do not use household cleaning agents. Damage to gas 

train components (valve/hose/regulator) can result. 

 

 

 

 

 

 

 

 

 

Connecting Regulator To The LP Tank

 

1. LP tank must be properly secured onto grill. (Refer to 

assembly section.) 

2. Turn all control knobs to the OFF position. 
3. Turn LP tank OFF by turning OPD hand wheel clockwise to 

full stop

4. Remove the protective cap from LP tank valve. Always use 

cap and strap supplied with valve.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. Hold regulator and insert nipple into LP tank valve. 

Hand-tighten the coupling nut, holding regulator in a straight 
line with LP tank valve so as not to crossthread the 
connection. 

 

 

 

 

 

 

Nipple has to be centered 

into the LP tank valve. 

 
 

 

If “growing” bubbles appear do not use or move the LP 
tank. Contact an LP gas supplier or your fire department! 

 

OPD Hand Wheel 

Safety Relief Valve 

Strap and Cap 

 

Type 1 outlet with 

thread on outside 

Do not insert a POL transport plug 
(plastic part with external threads) 
into the Type 1 tank valve outlet . It 
will defeat the Safety Relief Valve 

feature. 

Содержание 148.20125510









































Отзывы: