How to use the spotting scope
Mount the spotting scope on
a tripod.
Use the screw of the tripod
and fasten it to the screw
hole (1/4 screw hole) on the
bottom side of the scope’s
mounting plate.
screw hole for tripod
screw hole for tripod
Remove the cap in front of
the lens and extend the
lens hood.
Extending the lens hood
protects the lens against
rain drops. It also cuts out
excess sunrays, which
leads to a better effect
when looking through the
scope.
Rotate the cap on the
eyepiece to the left and
remove it. Be careful to not
use excessive force in order
to avoid removing the lens
itself.
2.
Locate the object and adjust
the spotting scope so that the
center of the scope is facing
the object. There is a sight line
on the lens hood which can be
used to get an approximate
idea when adjusting the scope
while looking for the object. It
is easier to see the object in
the field of view if the object is
aligned with the sight line.
While looking through the
eyepiece with one eye, turn
the coarse focusing ring on
the spotting scope body to
adjust the focus. For fine
tuning, turn the fine
focusing ring (next to the
coarse focusing ring) to
adjust the focus.
5.
The magnification can be
changed by turning the
zoom ring. When you have
changed the magnification,
turn the focusing ring again
to adjust the focus.
Adjust the eye point.
The eyepiece has a
twist-up aperture, which
should be extended for use
by non-glasses wearers. If
you are wearing glasses,
please do not extend the
eyepiece.
hood
lens
eyepiece
eyepiece
hood
sight line
sight line
sight line
coarse focusing ring
coarse focusing ring
coarse focusing ring
fine focusing ring
fine focusing ring
fine focusing ring
zoom ring
zoom ring
lens
※
For a smooth operation, it is advisable to focus at a lower
magnification first.
※
By loosening the lens barrel fixing screw, the body can
be rotated 360 degrees. The angle can be changed
according to the conditions of use.
※
This telescope is splash proof against rain and water
splashes. It is not suitable for use underwater. If it is
exposed to water, please wipe it completely off
afterwards.
※
As this product is splash proof, initial operation of the
zoom ring may be heavy.
lens barrel fixing screw
lens barrel fixing screw
zoom ring
Caution
●
●
●
●
●
●
●
●
Do not use the product for any unintended purposes.
Do not use it with smartphones which exceed 300g in weight. Due to the telescope’s structure, there are cases where you cannot use the
adapter for smartphones under 300g.
Please make sure that your smartphone is fully locked before attaching it the adapter.
When placing the smartphone on the adapter, make sure that the adapter does not come into contact with any switches on the side of the
smartphone. This may cause a malfunction.
When attaching the telescope to the adapter, please pay attention to balance. Bad balance carries the risk of the telescope dropping or
falling over during usage.
Please do not carry your smartphone while it is attached to this product. It may cause unrepairable damage.
We cannot accept any liability for damage to your smartphone in the event that it falls down. Please be very careful when using this
product.
When attaching the smartphone to the adapter, please be careful not to jam your fingers. Be especially careful when letting children use
the adapter.
Warning
Do no look into the sun with the spotting scope attached to the
smartphone adapter. Doing so will lead to blindness and permanent eye
damage. It will also cause damage to the smartphone device.
How to use the smartphone adapter
Part names
Smartphone adapter part names
Tripod Mounting
Section
Eyepiece Holder
Eyepiece Fixing Ring
Smartphone
Fixing Screw
Smartphone Holder
Eyepiece Holder
Fixing Screw
Available sizes for mounting
Smartphone size for mounting
Width: 54-97mm
Thickness: up to 13mm
Attachable eyepiece sizes
Height: 26-52mm
*
Width: over 14mm
*
Limited to circular shapes
How to attach your smartphone to the adapter
Turn the Smartphone Fixing
Screw and adjust it to a size
which fits your smartphone.
Place your smartphone in
the Smartphone Holder.
Please make sure that the
holder does not come into
contact with the switches
on the smartphone due to
the risk of malfunction.
Align the camera lens of
the smartphone with the
centre hole of the
Eyepiece Fixing Ring.
Turn the Eyepiece Fixing
Ring and attach it to the
eyepiece.
1.
7.
6.
4.
3.
- 2 -
- 3 -
1.
2.
3.
4.
Width
Width
Thickness
Height
