Kelly KLS Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 35

Kelly KLS Series Скачать руководство пользователя страница 24

Kelly KLS-M/N Brushless Motor Controller User’s Manual

V 2.5

21

function.Usually It is useful for electric boat project.You still can use the common 0-5K pot or
0-5V throttle for the controller.If you don't choose the joystick,you operated the throttle in this
way.The motor speed will increase when the throttle is from 0V to 5V.
If you enable joystick for this controller in user program,you will start the motor from 2.5V
position.2.6V to 5V is forward.2.4V to 0V is backward.
2.4V to 2.6V is the throttle dead zone.Customers can adjust the throttle dead zone in user
program also.
Please note the common throttle will spring back to original position if you release the throttle.
Suggestion:factory default is Disable.

(23)Three Gears switch:It is used for function of F-N-R control.
Please check the wiring diagram in the manual for F-N-R control.
Suggestion: Set according to the practical situation, factory default is Disable.

(20-A)Three Gears Switch
Value range: Enable and Disable
Functional description: If enabled, the Forward switch will be activated. Please see figure 4.1.
Suggestion: Set according to the practical situation, factory default is Disable.

(20-B)Foot Switch
Value range: Enable and Disable
Functional description: If enabled,the foot switch will be activated.The controller will not accept
the throttle signal if the foot switch is turned off. Please see figure 4.1.
Suggestion: Set according to the practical situation, factory default is Disable.

Configuration

Pin Status

Running

Status

Forward

Switch

Foot Switch

FWD_SW

(12)

REV_SW

(14)

Foot

(15)

Enable

Disable

OFF

OFF

x

Neutral

OFF

ON

x

Reverse

ON

OFF

x

Forward

ON

ON

x

Neutral

Disable

Enable

x

OFF

OFF

Can’t operate

x

ON

OFF

Can’t operate

x

ON

ON

Reverse

x

OFF

ON

Forward

Disable

Disable

x

OFF

x

Forward

x

ON

x

Reverse

Note: X means can be on or off

Figure 4.2

(24)Boost:If enabled,the controller will output max power for a while.
Boost function is just full throttle position when you turn on boost switch even if the throttle is not
operated at all.

«
...
22
23
24
25
26
...
»

Содержание KLS Series




































Отзывы:

Нет отзывов