Keithley KPCI-488 LPA Скачать руководство пользователя страница 29

Страница: 29 / 82

KPCI-488LPA-900-01 Rev. A / December 2008

Return to

Section Topics

2-3

Model KPCI-488LPA GPIB Controller Interface Card User’s Manual

Section 2: NI Command Compatible Functions

Introduction

This section contains information about the National Instruments™ (NI)

command compatible

functions and provides information on using the functions, as well as a reference section containing
syntax examples (C/C++, Visual Basic, etc.).

Appendix A

contains information on

NI command

compatible status codes

and

NI command compatible function error codes

NOTE

Refer to

Section 1

for

Keithley Command Compatible Functions

If you have any questions after reviewing this information, please contact your local Keithley
Instruments representative or call one of our Applications Engineers at 1-800-KEITHLEY (US only) or
visit our website at www.keithley.com.

Using NI Command Compatible functions

This section provides the fundamentals of building Windows

XP/2000/Vista applications using NI

command compatible functions and either Microsoft

Visual Basic or Microsoft Visual C/C++.

Microsoft Visual Basic (Version 6.0)

To create an application with NI command compatible functions and Visual Basic, follow these steps:

Step 1: Enter Visual Basic and open or create a project in which to use the NI command
compatible functions

To create a new project, select

New Project

from the

File

menu.

To use an existing project:

1. Open the file by selecting

Open Project

from the

File

menu. The

Open Project

dialog box

appears (

Figure 2-1

Open Project dialog box

2. Load the project by finding and double-clicking the project file name in the applicable directory.

1. National Instruments

™

and NI are trademarks of the National Instruments Corporation.

Содержание KPCI-488 LPA



















































































Результаты поиска

Содержание KPCI-488 LPA

Отзывы:

Похожие инструкции для KPCI-488 LPA

Бренды по названию

Популярные бренды

Keithley KPCI-488 LPA, Руководство пользователя

Результаты поиска

Содержание KPCI-488 LPA

Отзывы:

Похожие инструкции для KPCI-488 LPA

Бренды по названию

Популярные бренды