manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Front Panel Operation

4-20

5. The first channel spacing event will scan the first

channel in the scan list.

6. The next channel spacing event will scan the sec-

ond channel.

7. The next scan spacing event will pass operation

back into the channel layer.

8. The next channel spacing event will scan the first

channel.

9. The next channel spacing event will scan the sec-

ond channel and disarm (idle) the scanner.

Example 4:

ARM SPACING = MANUAL, GPIB, EXTERNAL or
TRIGLINK

SCAN SPACING = IMMEDIATE

CHANNEL SPACING = TIMER, EXTERNAL, GPIB, MAN-
UAL or TRIGLINK

1. Press OPEN ALL to open all channels and place

the Model 7001 in the idle state.

2. Press STEP to take the 7001 out of the idle state.
3. The arm spacing event allows operation to pass

into the scan layer.

4. Operation passes immediately into the channel

layer since IMMEDIATE scan spacing is selected.

5. The first channel spacing event will scan the first

channel in the scan list.

6. The next channel spacing event will select the sec-

ond channel.

7. Operation passes automatically back into the chan-

nel layer since IMMEDIATE scan spacing is select-
ed.

8. The next channel spacing event will select the first

channel.

9. The next channel spacing event will select the sec-

ond channel and disarm (idle) the scan.

Scanning notes: 

1. The STEP key is always functional during a scan

and can be used to provide a spacing event. For ex-
ample, if programmed for TIMER channel spacing,
the STEP key can also be used to select the next
channel.

2. Forbidden Channels cannot be entered into the

scan list.

3. With Single Channel enabled, only the lowest

numbered channel in a memory location (i.e. M1)
will close when selected.

4. Card Pair is functional during a scan. The channels

included in the scan list and the corresponding
channels for the other slot will be scanned.

Summary of scan keys:

OPEN ALL 

 Use to stop a scan, open all channels,

and place the Model 7001 in the scan idle state.

STEP 

 Use to take the Model 7001 out of the idle state;

and also, use to manually step through a scan.

4.5.5

Storing channel patterns (STORE and 

RECALL)

Any displayed channel pattern can be stored in memo-
ry locations M1 through M100. A channel pattern is
simply a pattern of open and closed channels.

Channel Patterns are not lost (cleared) when the instru-
ment is turned off. However, a Channel Pattern is
cleared if any of the following events occur:

1. A closed channel in the Channel Pattern becomes

unavailable. A channel can become unavailable by
changing a slot assignment (Card TYPE) or by
changing to a pole mode that reduces the number
of available channels.

2. A closed channel in the Channel Pattern becomes

restricted. A channel becomes restricted by adding
it to the restricted channel list.

The following examples demonstrate how a Channel
Pattern is lost:

1. Assume a Channel Pattern includes channel 1!21

as a closed channel and the assignment for slot 1 is
changed to a multiplexer card that has only 20
channels. Since channel 1!21 no longer exits, the
Channel Pattern is cleared.

2. Assume a Channel Pattern includes channel 1!1 as

a closed channel and the assignment for slot 1 is
changed to a matrix card. Since channel 1!1 is an in-
correct format for a matrix card, it no longer exists.
The Channel Pattern is cleared.

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

IDEC HS1C Series Instruction Sheet preview
HS1C Series
Бренд: IDEC Страницы: 5
IDEC HS5E Series Instruction Sheet preview
HS5E Series
Бренд: IDEC Страницы: 7
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Бренд: Quintum Страницы: 2
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Бренд: Gefen Страницы: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Бренд: ORiNG Страницы: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Бренд: Theben Страницы: 35
Omron D4N-1A20R Datasheet preview
D4N-1A20R
Бренд: Omron Страницы: 16
Wavetronix Click 223 Installation preview
Click 223
Бренд: Wavetronix Страницы: 3
Hisselektronik Safeline 2000 Light Manual For Programmering preview
Safeline 2000 Light
Бренд: Hisselektronik Страницы: 9
Omega OM-ESW-105-POE User Manual preview
OM-ESW-105-POE
Бренд: Omega Страницы: 17
Omron DZ Datasheet preview
DZ
Бренд: Omron Страницы: 6
Alcatel-Lucent OmniAccess 6000 Installation Manual preview
OmniAccess 6000
Бренд: Alcatel-Lucent Страницы: 76
infobit iMatrix H44H150 User Manual preview
iMatrix H44H150
Бренд: infobit Страницы: 27
MCOHome MH-S312 User Manual preview
MH-S312
Бренд: MCOHome Страницы: 3
Smart-M DVNET-4Duo User Manual preview
DVNET-4Duo
Бренд: Smart-M Страницы: 2
Trust SMART Home AWMR-230 User Manual preview
SMART Home AWMR-230
Бренд: Trust Страницы: 57
Raritan MasterConsole II MCC16 User Manual preview
MasterConsole II MCC16
Бренд: Raritan Страницы: 49
3Com OfficeConnect 3C16733A User Manual preview
OfficeConnect 3C16733A
Бренд: 3Com Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды