manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

 

Front Panel Operation

 

4-2

 

4.2.2

Power switch 

 

To turn on the power, simply push in the front panel
POWER switch. Power is on when the switch is at the
inner (1) position. To turn off power, press POWER a
second time to release the switch. 

 

4.2.3

Power-up sequence 

 

On power-up, the Model 7001 will go through the fol-
lowing sequence:

1. The instrument will perform self-tests on its

EPROM and RAM memory elements. If a failure is
detected, the instrument will lock up and display
the following message: 

 

No Comm Link 

 

Note: If a problem develops while the instrument
is under warranty, return it to Keithley Instru-
ments, Inc. for repair. 

2. If the instrument passes the self-tests, the firmware

revision levels and currently selected IEEE-488 ad-
dress will be displayed. An example of this display
is shown as follows: 

 

Model 7001

Rev. AXX AY  IEEE Addr = 07

 

where:

Rev. AXX is the firmware level for the main CPU.
Rev. AYY is the firmware level for the display CPU.
7 is the current IEEE-488 Address. Note that the in-
strument is shipped from the factory with the ad-
dress set to 7. 

3. The Model 7001 will then perform card identifica-

tion (Card ID). Card ID is required so that the
mainframe can configure itself to operate properly
for installed cards. Card ID is described as follows: 

 

Model 701X series cards 

 

 

 If a Model 701X series

card (i.e. 7011, 7012 or 7013) is installed in the
mainframe, it will be automatically identified. The
operator need not do anything. For example, if a

Model 7011 multiplexer card is installed in slot 1
and a Model 7012 matrix card is installed in slot 2,
the following message will be displayed briefly: 

 

#1 = 7011

#2 = 7012 

 

Non-701X series cards 

 

 

 The Model 7001 cannot

automatically identify non-701X series cards. The
model numbers of these cards are entered by the
user using the Card Configuration menu (see para-
graph 4.7). On power-up, the mainframe checks its
memory and displays the model number last en-
tered by the user. For example: 

 

#1 = 7052  #2 = NONE 

 

“7052” indicates that a Model 7052 card was last
assigned to slot 1. There may or may not be a Mod-
el 7052 card currently installed in slot 1. The mes-
sage “NONE” indicates that the user last
designated slot 2 to be empty, or the last card in-
stalled in the now empty slot was a Model 701X se-
ries card. Slot 2 may be empty or it may contain an
unassigned non-701X series card. 

“9990” or “9991” indicates that the slot was as-
signed by the user to simulate a switching card.
With “9990” assigned, the mainframe will operate
as if a 40 channel multiplexer card is installed. With
“9991” assigned, the mainframe will operate as if a
4

 

 ×

 

 10 matrix is installed. This simulation mode al-

lows you to develop and test a switching system
without having the card installed. 

 

NOTE

 

For non-701X series cards, make sure
that the power-up Card ID model
number messages correspond to what
is actually installed in the mainframe.
Use the Card Configuration menu (see
paragraph 4.7) to assign the correct
model numbers to the slots.

4. After card identification, the instrument will go to

the channel status display state (see paragraph 4.3
Display).

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Radial Engineering Gold Digger User Manual preview
Gold Digger
Бренд: Radial Engineering Страницы: 8
Radial Engineering BigShot ABY User Manual preview
BigShot ABY
Бренд: Radial Engineering Страницы: 2
Xantech AC1 Installation Instructions preview
AC1
Бренд: Xantech Страницы: 2
Qlogic SilverStorm 9000 Hardware Installation Manual preview
SilverStorm 9000
Бренд: Qlogic Страницы: 50
WAGO 852-112/000-001 Manual preview
852-112/000-001
Бренд: WAGO Страницы: 30
RDL EZ-HSX4 Installation And Operation Manual preview
EZ-HSX4
Бренд: RDL Страницы: 4
Avocent SwitchView SC8 DVI Specifications preview
SwitchView SC8 DVI
Бренд: Avocent Страницы: 2
SMART Hub VE220 Installation And User Manual preview
Hub VE220
Бренд: SMART Страницы: 46
Kobold PPS-1201 Operating Instructions Manual preview
PPS-1201
Бренд: Kobold Страницы: 10
Crestron CLW-LSWEX-1GD Installation And Operation Manual preview
CLW-LSWEX-1GD
Бренд: Crestron Страницы: 2
Oehlbach UltraHD Switch 3:1 User Manual preview
UltraHD Switch 3:1
Бренд: Oehlbach Страницы: 20
Soyntec Nexoos 370 Series User Manual preview
Nexoos 370 Series
Бренд: Soyntec Страницы: 7
Lantech TPGS-L6208XT User Manual preview
TPGS-L6208XT
Бренд: Lantech Страницы: 24
Raritan PC-Share Installation And Operation preview
PC-Share
Бренд: Raritan Страницы: 4
Pathway connectivity solutions 6716 User Manual preview
6716
Бренд: Pathway connectivity solutions Страницы: 34
Contec SH-9008AT-POE Reference Manual preview
SH-9008AT-POE
Бренд: Contec Страницы: 38
Seastar Solutions pro-trim PT1000 Installation Manual preview
pro-trim PT1000
Бренд: Seastar Solutions Страницы: 2
Xantech HD88C Installation Instructions Manual preview
HD88C
Бренд: Xantech Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды