Keithley 7001 Скачать руководство пользователя страница 231

Страница: 231 / 353

IEEE-488 Reference

5-112

10 OUTPUT 707; “:stat:oper:cond?”

20 ENTER 707; A$

30 PRINT A$

40 END

Line 10

Queries the Operation Condition Register.

Line 20

Addresses the 7001 to talk.

Line 30

Displays the decimal value that defines which bits in the register are set.

:PREset

:STATus:PREset

Return 7001 to default conditions

:stat:pres

When this command is sent, the SCPI event registers are affected as follows:

1. All bits of the positive transition filter registers are set to one (1).

2. All bits of the negative transition filter registers are cleared to zero (0).

3. All bits of the following registers are cleared to zero (0):

A. Operation Event Enable Register.

B. Questionable Event Enable Register.

4. All bits of the following registers are set to one (1):

A. Trigger Event Enable Register.

B. Arm Event Enable Register.

C. Sequence Event Enable Register.

Note: Registers not included in the above list are not affected by this command.

The following programming example demonstrates how to use the :PRESet command of the
STATus subsystem:

OUTPUT 707; “:stat:pres”

Programming

example

5.16.5

Short-form

format

Description

Programming

example

:STATus Subsystem

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Результаты поиска

Содержание 7001

Отзывы:

Похожие инструкции для 7001

Бренды по названию

Популярные бренды

Keithley 7001, Инструкция по эксплуатации

Результаты поиска

Содержание 7001

Отзывы:

Похожие инструкции для 7001

Бренды по названию

Популярные бренды