manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

IEEE-488 Reference

5-24

With the Timer control source selected
(:ARM:LAYer2SOURce  TIMer), operation will immedi-
ately proceed into the channel layer on the initial pass
through Arm Layer 2. Each additional scan will not occur
until the programmed timer interval elapses. The timer can
be set to an interval from 1msec to 999999.999 seconds.

With the Manual control source selected
(:ARM:LAYer2:SOURce  MANual), the instrument will
wait until the front panel STEP key is pressed. Note that the
Model 7001 must be taken out of remote (press LOCAL key
or send LOCAL 707 over bus) before it will respond to the
STEP key. With the Bus control source selected
(:ARM:LAYer2:SOURce BUS), the instrument will wait un-
til a bus trigger is received (GET or *TRG). With the Exter-
nal control source selected (:ARM:LAYer2:SOURce

EXTernal), the instrument will wait until an input trigger

(via EXTERNAL TRIGGER connector on rear panel) is re-
ceived. With the Trigger Link control source selected
(:ARM:LAYer2:SOURce  TLINk), the instrument will wait
until an input trigger is received (via TRIGGER LINK). With
the Hold control source selected (:ARM:LAYer2:SOURce

HOLD), the instrument will not respond to any of the con-

trol source events. 

After the programmed scan event is detected, the instrument
will wait for the programmed Delay to time out. The
:ARM:LAYer2:DELay  <n> command is used to set the De-
lay (where n = 0 to 999999.999 seconds). The *RST and
:SYSTem:PRESet commands set the Delay to zero seconds. 

As can be seen in the flowchart, there are three paths that al-
low operation to loop around the control source. Two of these
paths also loop around the Delay. These three paths are de-
scribed as follows: 

1. When the Source Bypass is enabled (:ARM:TCONfig-

ure:DIRection  SOURce) and the External or Trigger
Link control source is selected, operation will loop
around the control source on the initial pass through arm
layer 2. If programmed for another scan (scan count >
1), the bypass loop will not be in effect even though it
will still be enabled. The Source Bypass loop will reset
(be in effect) if operation goes back into arm layer 1. 

Enabling the Source Bypass also enables the Output
Trigger. When operation returns to arm layer 2 from the
trigger layer, an output trigger pulse will occur. If the

Trigger Link control source is selected, the output trig-
ger pulse will be available on the programmed TRIG-
GER LINK output line. For all other control source
selections, the output trigger pulse will be available at
the CHANNEL READY connector. The Output Trigger
in this layer is disabled when the Source Bypass is dis-
abled (:ARM:TCONfigure:DIRection  ACCeptor). 

2. Each time the :ARM:LAYer2:IMMediate command is

sent, operation will loop around the scan control source
and the Delay. It is used when you do not wish to wait
for a programmed scan event to occur (or when the Hold
control source is selected).

3. Each time the :ARM:LAYer2:SIGNal command is sent,

operation will loop around the scan control source. This
path functions the same as :ARM:LAYer2:IMMediate
except that it does not loop around the Delay. 

After all other operations in the next layer have been com-
pleted, the instrument can be returned to Arm Layer 2 by pro-
gramming the instrument for additional scans. The
:ARM:LAYer2:COUNt  <n> command can be used to set
the scan count to a finite value (where <n> = 1 to 9999) or
for an infinite (<n> = INF) number of scans. The *RST com-
mand sets the scan count to one and the :SYSTem:PRESet
command sets the scan count to infinite. 

After the instrument leaves arm layer 2, operation proceeds
to the Channel Layer (Trigger Layer). 

Trigger layer

NOTE

For front panel operation, this layer is
called the channel layer.

In general, measure events control the channel scan rate.
With the Immediate control source selected (:TRIG-
ger:SOURce  IMMediate), operation immediately proceeds
to the Delay. The *RST command also sets the measure con-
trol source to Immediate. With one of the other control sourc-
es selected, the instrument will wait until the appropriate
event occurs.

With the Timer control source selected (:TRIGger :SOURce
TIMer), the first channel will be scanned immediately. Each
additional will be scanned at a rate determined by the pro-
grammed timer interval (1msec to 999999.999 seconds).

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

ABB EDS500 Series Operating Instruction preview
EDS500 Series
Бренд: ABB Страницы: 7
Painless Performance Products 50201 Installation Instructions preview
50201
Бренд: Painless Performance Products Страницы: 2
Cables to Go 40020 Instruction Manual preview
40020
Бренд: Cables to Go Страницы: 4
Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES How To Connect preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Бренд: Jabra Страницы: 4
Eaton P3-63/I4 Instruction Leaflet preview
P3-63/I4
Бренд: Eaton Страницы: 2
Hansen HLL Series Specifications, Applications, Service Instructions & Parts preview
HLL Series
Бренд: Hansen Страницы: 4
Lindy 32351 Manual preview
32351
Бренд: Lindy Страницы: 70
Ubiquiti EdgeSwitch 10 XP Quick Start Manual preview
EdgeSwitch 10 XP
Бренд: Ubiquiti Страницы: 13
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Бренд: Dahua Страницы: 3
X-keys XK-60 Product Manual preview
XK-60
Бренд: X-keys Страницы: 4
senva C-2330 Installation Instructions preview
C-2330
Бренд: senva Страницы: 2
MTHTrains RealTrax O-3 User Manual preview
RealTrax O-3
Бренд: MTHTrains Страницы: 16
Madison M8000-C Installation And Maintenance preview
M8000-C
Бренд: Madison Страницы: 2
H3C S5500-28C-EI Installation Manual preview
S5500-28C-EI
Бренд: H3C Страницы: 96
NVision NV8288 User Manual preview
NV8288
Бренд: NVision Страницы: 86
Icy Box IB-HUB1410-C3 Quick Installation Manual preview
IB-HUB1410-C3
Бренд: Icy Box Страницы: 12
Cable Electronics CE Labs HSW44C Instruction Manual preview
CE Labs HSW44C
Бренд: Cable Electronics Страницы: 12
Audiovox Signal Distribution Box SDB45 Owner'S Manual preview
Signal Distribution Box SDB45
Бренд: Audiovox Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды