Keithley 4200A-SCS Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 1381

background image

Model 4200A-SCS Parameter Analyzer Reference Manual

Section 5: Pulse measure and pulse generator units

4200A-901-01 Rev. C / February 2017

5-11

Shield connections

For multiple PMU channels, you should connect the shields (common LO) from all PMU channels as
close as possible to the DUT. You reduce inductance by minimizing the loop area of the shield
connections. The figure in

Using a SMA to SSMC adapter cable to connect pulse card to DUT

(on

page 5-16) and the

(on page 5-18) figures illustrate proper shield connection schemes

using the supplied cabling.

Cable length

Use the shortest possible cable length to achieve the highest frequency output, the best pulse shape,
and the best results. Here are reasons to avoid using longer cable lengths:

•

Longer cable lengths have longer reflection times, which can slow down transmission times.

•

Longer cables may have impedance mismatches, which can cause distortions.

•

Higher capacitance in longer cables causes higher capacitive charging effects during the pulse
transitions (see

PMU capacitive charging/discharging effects

(on page 5-42)).

Only use the white SMA coaxial cables that are sup

plied with the PMU and RPM. These are 50 Ω

cables that match the internal 50 Ω resistance of the PMU. The PMU is supplied with 6.5 ft (2 m) SMA
cables and the RPM is supplied with 8 in. (20 cm) SMA cables. Always use the 8 in. (20 cm) SMA
cables with the RPM.

High frequency connections

Use these connection guidelines for high-speed testing (pulse width <1 µs).

•

Use cables and connectors optimized for high frequency (at least 150 MHz). The SMA coaxial
cables supplied with the PMU and RPM are rated for high frequency.

•

Probe manipulators must be rated at least 150 MHz.

•

Properly connect the shields of the coaxial cables and minimize the loop area of the shield
connections (see

Shield connections

(on page 5-11)).

•

Minimize cable length (see

(on page 5-11)).

•

Use a signal path that matches the impedance of the instrument (50

Ω). The SMA cables

supplied with the PMU and RPM are 50

Ω.

«
...
202
203
204
205
206
...
»

Содержание 4200A-SCS






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4200A-SCS

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Бренд: FCI Страницы: 44

Бренд: FCI Страницы: 36

Бренд: FCI Страницы: 26

MIC TRAC MT-3000

Бренд: GAGEMAKER Страницы: 20

ORBISPHERE 3624

Бренд: Hach Ultra Страницы: 12

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

Бренд: Omega Страницы: 170

Бренд: bmcm Страницы: 5

Бренд: Tektronix Страницы: 48

Бренд: Aalborg Страницы: 56

Бренд: Oberheim Страницы: 41

Бренд: Newton Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды