manualshive.com logo in svg

Keithley 2010, Руководство по обслуживанию, Страница: 36 / 134

Поделиться
Скачать
Keithley 2010 Скачать руководство пользователя страница 36

NOTE

If your calibrator cannot output the values recommended in 

Table 2-3

, use the left and 

right arrow keys, and the up and down range keys to set the Model 2010 display value 
to match the calibrator output voltage.

Resistance calibration

Completing the 100V DC calibration step ends the DC voltage calibration procedure. The 

Model 2010 will then prompt you to connect 10

Ω

. Follow these steps for resistance calibration:

1.

Set the calibrator output for resistance, and turn on external sense.

NOTE

Use external sense (4-wire 

Ω

) when calibrating all resistance ranges. Be sure that the 

calibrator external sense mode is turned on.

2.

Perform the calibration steps summarized in 

Table 2-4

. For each step:

•

Set the calibrator to the indicated value, and place the unit in operate. (If the calibrator 
cannot output the exact resistance value, use the Model 2010 left and right arrow keys 
and the range keys to adjust the Model 2010 display to agree with the calibrator 
resistance.)

•

Press the ENTER key to calibrate each point.

•

Wait for the Model 2010 to complete each step before continuing.

Table 2-3

DC volts calibration summary

Calibration step

Calibrator voltage

Allowable range

+10V
-10V
100V

+10.00000V
-10.00000V
+100.0000V

+9V to +11V
-9V to -11V
+90V to +110V

Table 2-4

Ohms calibration summary

Calibration step

Calibrator resistance*

Allowable range

10

Ω

1k

Ω

10k

Ω

100k

Ω

1M

Ω

10

Ω

1k

Ω

10k

Ω

100k

Ω

1M

Ω

9

Ω

 to 11

Ω

0.9k

Ω

 to 1.1k

Ω

9k

Ω

 to 11k

Ω

90k

Ω

 to 110k

Ω

0.9M

Ω

 to 1.1M

Ω

* Nominal resistance. Adjust Model 2010 calibration parameter to agree with actual value.

Calibration

2-9

Содержание 2010







































































































































Отзывы:

Нет отзывов