Keithley 2010 Скачать руководство пользователя страница 32

Страница: 32 / 134

Recommended equipment

lists the recommended equipment you need for comprehensive, DC only, and AC

only calibration procedures. You can use alternate equipment, such as a DC transfer standard and
characterized resistors, as long as that equipment has specifications at least as good as those
listed in the table.

Aborting calibration

You can abort the front panel calibration process at any time by pressing EXIT. The

instrument will then ask you to confirm your decision to abort with the following message:

ABORT CAL?

Press EXIT to abort calibration at this point, or press any other key to return to the calibration

process.

NOTE

The Model 2010 will not respond to any remote programming commands while the
ABORT CAL? message is displayed.

Table 2-1

Recommended equipment for comprehensive, DC-only, or AC-only calibration

Fluke 5700A calibrator:

DC voltage

AC voltage

(1kHz, 50kHz)*

DC current

AC current

(1kHz)

Resistance

±10V:±5ppm
100V:±7ppm

10mV:±710ppm
100mV:±200ppm
1.0V:±82ppm
10V:±82ppm
100V:±90ppm
700V:±85ppm

10mA:±60ppm
100mA:±70ppm
1A:±110ppm

100mA:±190ppm
1A:±690ppm
2A:±670ppm

Ω

:±28ppm

Ω

:±12ppm

10k

Ω

:±11ppm

100k

Ω

:±13ppm

Ω

:±18ppm

Keithley 8610 Low-thermal shorting plug

* 1kHz specifications. 10mV and 700V points require 1kHz only. All calibrator specifications are

90-day, 23°C ±5°C specifications and indicate total absolute uncertainty at specified output.

Calibration

2-5

Содержание 2010






































































































































Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды

Keithley 2010, Руководство по обслуживанию

Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды